Estimate the torque required at the base of a flag pole

Assignment Help Mechanical Engineering
Reference no: EM13212342

Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole. ( if needed, use air density(p)=1.2kg/m^3, µ=1.8*10^(-5)Pa*sec; water properties:p=10^3 kg/m^3, µ=10^(-3)Pa*sec)

Reference no: EM13212342

Questions Cloud

What southwest airlines sought to accomplish for stakeholder : Identify what Southwest Airlines sought to accomplish for its stakeholders and evaluate Southwest Airlines' actions with respect to employees and customers.
Explain step by step mechanism for the reaction of butanal : step by step Mechanism for the reaction of butanal with methanol under acid catalyzed conditions?
Calculate the overall train value : calculate: a) the overall train value. b) the output rational speed at shaft 5. c) the output torque at shaft 5. Relevant gear data is= NA= 17, NB= 36, NC= 19, ND= 41, worm E = double lead, worm G = triple lead, NH= 37?
Explain the change in volume from adding hcl is negligible : What volume of 1 M HCl do you have to add to change the pH of the solution to 6? Assume that the change in volume from adding HCl is negligible. Recall that pH = pKa + log([A-]/[HA]. I cannot, for the life of me, figure this out.
Estimate the torque required at the base of a flag pole : Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole.
Determine the angle theta degrees : However, even when the cylinder is pressurized, the torque T is still sufficient to keep the seam closed so that no water leaks out. Determine the angle theta degrees that requires the minimum torque T to keep the seam closed. (Hint: use Mohr's ci..
What arrangements is zaneb likely to encounter : Zaneb is a high-school teacher and is well known in her community for her honesty and integrity. She is shopping for a new car and plans to borrow the money to pay for it from her local bank. Does Zaneb create any moral hazard or adverse selection..
Estimate the infiltration flow rate : Estimate the infiltration flow rate if the window is partially open (assuming the window open area is 2 meter squared).
Depict the structure of the product that is formed : Draw the structure of the product that is formed when (1R,3S)-3-methylcyclohexan-1-ol is treated with the following reagents

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the velocity of the collars a and b

the motion of the slender 10kg rod AB is guided by collars of negligible mass that slide freely on the vertical and horizontal rods. knowing that the bar is released from rest when θ=30, determine the velocity of the collars A and B when θ = 60.

  Explain working with boiler suspension bolts

Working with boiler suspension bolts. An HRT boiler is 4766mm long and 3533mm in diameter. It has 66 steel tubes with a diameter of 9mm. The total dry weight of the boiler is 2.565 tonnes

  Determine the moments of inertia

two 20mm steel plates are welded to a rolled S section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.

  Compute reactions of a simply supported continuous beam

Calculate reactions of a simply supported continuous beam. A beam is simply supported at the ends and is continuous over two spans.

  An airfoil of surface area 1ft squared is tested for lift

Lift coefficient (Cl) and lift (L), An airfoil of surface area 1ft squared is tested for lift (L) in a wind tunnel. At an angle of attack of 5 degrees with standard air of density 0.0024 slugs/ft cube at a speed of 100 ft/sec

  Explain specific load and heat generated per minute

Design Engineering: Find Specific Load and Heat Generated Per Minute, A load of 6400 Kg is carried by a journal rotating in a 270 mm bearing diameter and 400 mm long. Find the specific load on the bearing and the heat generated per minute in the b..

  Determine the temperature of the electric heater element

Determine the temperature of the electric heater element and drawing of the temperature profile.

  Manufacturing processes-determine the velocity of shearing

Determine the velocity of shearing along the shear plane and the velocity of sliding at the tool-chip interface and find the work done per minute in shearing the metal and against the friction.

  Design problem - piston and flywheel

Design Problem - Piston and Flywheel : Analyze the motion of the crankshaft AB and flywheel for 0 ≤ θ ≤ 4Π (two complete rotations of the crankshaft, or all four cycles, beginning and ending at TDC), for different values of the four design paramete..

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Determine the resultant force applied

A short post AB has a commercially manufactured eyebolt screwed into its end. Three cables attahced to the eyebolt apply forces shown.

  Explain graphs for static force systems

Find graphically the forces f1 and f2 in the crane. The triangle is standing up with a 90 degree angle next to the wall on top, with f1 pointing towards it

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd