Estimate the skin friction drag on the aircrafts fuselage

Assignment Help Mechanical Engineering
Reference no: EM13518856

(a) Water flows into a smooth pipe from a large, still reservoir, as shown in Figure. The pipe entrance is rounded with a large radius to prevent separation. The boundary layer on the inside of the pipe is laminar, and it thickens with streamwise distance x. Classical theory tells us that the entry length for laminar flow in such a pipe is given as follows:

Le/D = 0.06 ReD for ReD < 2300

Making appropriate assumptions, use boundary layer theory to confirm that this result is reasonable. Discuss the validity of any assumptions you make.

Discuss whether, in this analysis, you should use the 99% thickness, the momentum thickness or the displacement thickness.

(b) A new passenger aircraft is cruising as 360 km/h in still air. The aircraft's fuselage is 50m long, has a circular cross-section of nearly constant diameter, and has a surface area of 740m2. The aircraft's surface has a roughness height (e) of 1.0 mm.

(i) Determine whether laminar-to-turbulent transition occurs in the boundary layer of the fuselage. If transition occurs, where does it occur?

(ii) Estimate the 99% thickness (δ) of the boundary layer at the downstream end of the fuselage.

(iii) Estimate the skin friction drag on the aircraft's fuselage.

(iv) Estimate the skin friction drag on the fuselage if the boundary layer is laminar everywhere. Note: Flat plate drag coefficient data are plotted in Figure 6 at the end of this question paper.

1868_Friction drag on the aircrafts fuselage.png

Figure:Pipe entry region

Reference no: EM13518856

Questions Cloud

According to nietzsche-concepts good and bad originate : According to Nietzsche, where did the concepts “good” and “bad” originate? How did “good” and “bad” get transformed into “good” and “evil?” In your response be sure to explain how “bad” and “evil” are distinct and different concepts.
What is leibniz nature of perception : What is Leibniz nature of perception? Please help in detail im completely lost, and confused. Discuss Leibniz’ two proofs of God’s existence in detail for better understanding.
What is the tension in the right-handed cable : A mass M is suspended using two cables which make angles of theta_1 and theta_2 with the horizontal across the top. What is the tension (T_2) is the right-handed cable
Find the minimum speed at the top of the circle : A 0.250 kg ball attached to a string s being swung in a vertical circle, like a roller coaster doing a loop-de-loop, with a radius of 1.15 m. What is the minimum speed at the top of the circle to keep the string from going slack
Estimate the skin friction drag on the aircrafts fuselage : Determine whether laminar-to-turbulent transition occurs in the boundary layer of the fuselage. If transition occurs, where does it occur - Estimate the skin friction drag on the aircraft's fuselage.
Calculate the speed of the elevator : An elevator cable breaks when a 975 kg elevator is 24.5 m above the top of a huge spring (k = 8.00 x 10^4 N/m) at the bottom of the shaft. Calculate the speed of the elevator just before striking the spring
What was the project of the pre-socratic philosophers : What was the project of the pre-socratic philosophers? on what charges was socrates tried, convicted and sentenced to the death? what did he do to bring about this situation? what claim by Galileo got him in trouble with church authorities? what did ..
Calculate the final kinetic energy of the block : A 6.30 kg block is pushed 9.45 m up a smooth 40 degree inclined plane by a horizontal force of 70 degrees north. Calculate the final kinetic energy of the block
Rights-based ethical theories : Rights-based ethical theories:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum flexural strength

Immediately before failure, the testing machine records a force (F) of 50N, and a deformation (δ) of 2mm. We need to determine the maximum flexural strength (σ)

  Determine the volume of chamber

the entire assembly is placed in an environment whose temperature is 200c. determine the volume of chamber 1 when thermodynamic equillibrium has been estabilished.

  Strain-based forming limit for three options

Submit yield surface, stress-ratio and r-value plots including EXP, von Mises, Hill (1948)-M1, and Hill (1948)-M2 - Strain-based forming limit for three options

  What is the percent span for the old and new setpoints

In order to increase production rate, a reactor setpoint was increased from 160 psig to 190 psig. The reactor pressure transmitter was recalibrated from 0- 200 psig to 0- 300 psig. What is the percent span for the old and new setpoints?

  Explain steady flow air compressor

A steady flow air compressor compresses 50 lb/min from 14 psia and 80 degrees F to a discharge state at 45 psia and 300 degrees F. Heat departs from the air only via circulating water that enters the jacket at 75 degrees F and leaves at 95 degrees..

  An air compressor takes air from outdoors at 28deg c and

an air compressor takes air from outdoors at 28deg c and 101.2kpa and compresses it to 790kpa and 50 deg c. the air

  Determine the surface temperature of the wire

Determine the surface temperature of the wire during a windy day when the air temperature is 10°C and the wind is blowing across the transmission line at 50 km/h.

  Specifies that just the data points be marked with a circle

Specifies that just the data points be marked with a circle. Showing the general trend of safety as a function of dia, with the actual data points marked by a circle. Is that explanation of the plot command still a little opaque?

  Minimize the internal protrusion of the drum

Design the number of teeth and depth of teeth need be chosen. Considerations include the turn angle for each stroke, the bearing stress on the teeth and pins and shear stress on the teeth.

  Pumps and heat recovery

Energy in the home, personal energy use and home energy efficiency. Efficient use of ‘waste' heat and renewable heat sources.

  A rigid tank has a volume of 006m3 and initially contains a

a rigid tank has a volume of 0.06m3 and initially contains a two-phase liquid-vapour mixture of nbsph2o at a pressure

  A cast-iron tube is used to support a compressive load

a cast-iron tube is used to support a compressive load. knowing that e 69 gpa and that the maximum allowable change in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd