Estimate the overall heat transfer coefficient u

Assignment Help Mechanical Engineering
Reference no: EM131337466

A thin-walled tube with a diameter of 6 mm and length of 20 m is used to carry exhaust gas from a smoke stack to the laboratory in a nearby building for analysis. The gas enters the tube at 200°C and with a mass flow rate of 0.003 kg/s. Autumn winds at a temperature of 15°C blow directly across the tube at a velocity of 5 m/s. Assume the thermophysical properties of the exhaust gas are those of air.

(a) Estimate the average heat transfer coefficient for the exhaust gas flowing inside the tube.

(b) Estimate the heat transfer coefficient for the air flowing across the outside of the tube.

(c) Estimate the overall heat transfer coefficient U and the temperature of the exhaust gas when it reaches the laboratory.

Reference no: EM131337466

Questions Cloud

Discuss various types of communications you will need to use : Discuss various types of communications you will need to use on the project, what stakeholder(s) each type would address and the frequency of each communication type. You may choose to use a table for this information.
What is the maximum rate of heat transfer from the vessel : Heat is to be removed from a reaction vessel operating at 75°C by supplying water at 27°C and 0.12 kg/s through a thin-walled tube of 15-mm diameter. The convection coefficient between the tube outer surface and the fluid in the vessel is 3000 W/m..
Practitioner attempt to change an organization culture : How would an OD practitioner attempt to change an organization's culture? Under what conditions are transformational changes necessary?
Which alternative should be chosen : BC Minerals is considering a new production process.- Using the equivalent annual annuity method, which alternative should be chosen?
Estimate the overall heat transfer coefficient u : Estimate the overall heat transfer coefficient U and the temperature of the exhaust gas when it reaches the laboratory.
Define and provide an example for halo effect : Define and provide an example for the following terms: halo effect, fundamental attribution error, propinquity, self-disclosure, and stereotyping
Explain the economics of cost floor pricing : 1. Explain the economics of cost floor pricing. 2. The gray market is often compared to financial arbitrage. Explain the significance of this comparison. 3. Describe the vehicle of channel power of manufactures. ... wholesalers and retailers.
Which cooling unit should be purchased and why : Germania Corporation is considering replacing its plant cooling unit.- The marginal cost of capital is 19 percent. Which cooling unit should be purchased? Why?
What situational factors exist that may affect performance : What, if any, situational factors exist that may affect the project team's performance? What are some project pitfalls you will want to watch out for as you execute this project?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd