Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
To what value could the gear hardness be reduced in Problem 15.31, without making the gear teeth weaker than the pinion teeth based on surface fatigue?
Problem 15.31
A pair of mating gears have 20° full-depth teeth with a diametral pitch of 8. Both gear and pinion are made of steel heat-treated to 350 Bhn, and both have a face width of 1.0 in. The teeth are cut with a top-quality hobbing operation. The pinion has 20 teeth and rotates 1100 rpm. It is mounted outboard on the shaft of an electric motor, and drives a 40-tooth gear that is positioned inboard on an accurately mounted blower shaft. The design life corresponds to 5 years of 60 hours/week, 50 weeks/year operation. Using a reliability of 99% and a safety factor of 1.5, estimate the horsepower that can be transmitted, based only on bending fatigue.
What are the roof SSE keys hard-coded within your Web browser of choice? When were these keys created? When do they expire?
a gas turbine brayton cycle operates with an intercooler a re-heater and a regenerator. air enters the engine at 14 psi
An electric motor, of mass m = 100 kg and operating speed = 1800 rpm is fixed at the middle of a clamped-clamped steel beam of rectangular cross section, as shown in Fig. 12.32. Design the beam such that the natural frequency of the system exceeds..
A steam turbine has an inlet of 2 kg/s water at 1000 kPa, 350oC and velocity of 15 m/s. The exit is at 100 kPa, x = 1 and very low velocity. Find the specific work and the power produced.
A PM DC motor is rigidly coupled to a fan; the fan load torque is described by the expression TL = 5 + 0.05ω + 0.001ω2, where torque is in Newton-meters and speed in radians per second. The motor has kaφ = kT φ = 2.42; Ra = 0.2 Q, and the inductance ..
a gas turbine burns methane with 150 theoretical air. assume the air is 25 degrees celsius 100 kpa and has a relative
a concrete slab measuring 0.3m x 4m x 6m initially at 298 k is exposed to the sun for several hours after which its
Two points on a stress-strain curve for a material are σ = 278 MPa at ε = 0.08 and σ = 322 MPa at ε = 0.16. A. Find K and n in the power-law approximation and predict σ at ε = 0.20.
the springs of an automobile trailer are compressed 10.6 cm under its weight. find the critical speed when the trailer
calculate the transverse modulus of the peek/carbon fiber composite with 30% volume fraction by tow method. the modulus of peek is 3.8 GPa and the modulus of the carbon fiber is 400GPa. assume the reinforcing factor.
Using the standard Fe-C phase diagram, draw a vertical line for each of the following steel alloys corresponding to their carbon content: AISI 1018, AISI 1045, AISI 1095, AISI 4140. Draw a point on the line for each alloy at 800oC and 425oC and descr..
A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd