Estimate the factors of safety ny and nf using a a gerber

Assignment Help Mechanical Engineering
Reference no: EM13640340

A cold-drawn AISI 1018 steel bar similar to the component shown in the diagram of Table A- 15-1 is subjected to an axial load fluctuating between -800 and 3000 lb. Estimate the factors of safe- ty ny and nf using (a) a Gerber fatigue failure criterion as part of the designer's fatigue diagram, and (b) ASME-elliptic fatigue failure criterion as part of the designer's fatigue diagram. Assume d = 0.25 in., w = 1 in., and h = 0.375 in.

Reference no: EM13640340

Questions Cloud

The mean iq score of adults is 100 with a standard : the mean iq score of adults is 100 with a standard deviation of 15. use the empirical rule to find the percentage of
A 050 mol sample of oxygen gas is confined a 0deg c in a : a 0.50 mol sample of oxygen gas is confined a 0deg c in a cylinder. the initial pressure in the cylinder is 1.0 atm. if
The mean iq score of adults is 100 with a standard : the mean iq score of adults is 100 with a standard deviation of 15. use the empirical rule to find the percentage of
The beam of neutral hydrogen atoms with a speed of 104 ms : the beam of neutral hydrogen atoms with a speed of 104 ms along the x-axis enters a 1m long region where there is an
Estimate the factors of safety ny and nf using a a gerber : a cold-drawn aisi 1018 steel bar similar to the component shown in the diagram of table a- 15-1 is subjected to an
Suppose that on a statistics test the mean greade in a : suppose that on a statistics test the mean greade in a class is 75 and the population standard deviation is 8. assume
A sample conaining both hcl and hno3 had a density of : a sample conaining both hcl and hno3 had a density of 1.083gml. a 30.00 ml amount of this sample required 25.78 ml of
An electron initially traveling at a speed of 105 ms enters : an electron initially traveling at a speed of 105 ms enters a region where there is a uniform magnetic field of 2t
The number of ships to arrive at a harbor on any given day : the number of ships to arrive at a harbor on any given day is a random variable represented by x. the probability

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  It is heated as it passes through the tube so that it

water enters one end of a long coiled tube at 5000 kpa 220c at a steady rate of 2.20kgs. it is heated as it passes

  A piston cylinder device contains 05 kg of water at 10mpa

a piston cylinder device contains 0.5 kg of water at 1.0mpa and 400oc. now it is cooled to 1mpa in sat-v phase.

  The flywheel of a punching machine has a mass of 300 kg and

the flywheel of a punching machine has a mass of 300 kg and a radius of gyration of 600 mm. each punching operation

  While trapped in a cylinder 227 kg of air is compressed

while trapped in a cylinder 2.27 kg of air is compressed isothermally with a water jacket being used around the

  A sphere of diameter 100 mm rotating at a rate of 286 rpm

a sphere of diameter 100 mm rotating at a rate of 286 rpm is situated in a stream of water 15 degree c that has a

  Given the answer to part a and the data below at 29815 k

aat t1000 k caclulate kp and delta gsubstance mole co2 27.1 h227.1 co 22.9 h2o 22.9b given the answer to part a and

  Find a cylindrical container

Find a cylindrical container that is large enough that it takes at least one minute to drain (you may have to create an opening at or near the bottom that gives the right behavior.

  Calculate its elongation

Consider a cylindrical titanium wire 3.0 mm in diameter and 2.5 x 104 mm long. Calculate its elongation when a load of 500N is applied, assuming that the deformation is totally elastic.

  Air at 15 c ows over a at plate a heater strip 10 cm long

air at 15 ? c ?ows over a ?at plate. a heater strip 10 cm long is placed on the plate at a distance 15 cm from the

  A car is travelling over a hill if using a cartesian

a car is travelling over a hill. if using a cartesian coordinate system with origin at the top of the hill the hills

  A subway train is being designed for operation between two

a subway train is being designed for operation between two stations a and b which are 2 km apart. if the maximum

  Calculate the velocity v of the collar

Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd