Estimate the best efficiency point and the maximum

Assignment Help Mechanical Engineering
Reference no: EM13623095

A centrifugal pump with backward-curved blades has the following measured performance when tested with water at 20°C:

Q, gal/min: 0 400 800 1200 1600 2000 2400

H, ft: 123 115 108 101 93 81 62

P, hp: 30 36 40 44 47 48 46

(a) Estimate the best efficiency point and the maximum efficiency. (b) Estimate the most efficient flow rate, and the resulting head and brake horsepower, if the diameter is doubled and the rotation speed increased by 50%.

Reference no: EM13623095

Questions Cloud

Last year emery industries had 450 million of sales and 225 : last year emery industries had 450 million of sales and 225 million of fixed assets so its fixed assetssales ratio was
Discuss the sequence of actions that occur in the operation : discuss the sequence of actions that occur in the operation of the control system for a traffic light that includes
The d ab of naphthalene in air at 318 k is 692 10 -6 m : a sphere of naphthalene having a radius of 2mm is suspended in a large volume of shell air at 318 k and 1 atm. the
Find the test statistic f to test the claim that the : find the test statistic f to test the claim that the populations have the same mean.brand 1brand 2brand
Estimate the best efficiency point and the maximum : a centrifugal pump with backward-curved blades has the following measured performance when tested with water at 20degcq
This year mitchell received a 600 refund of state income : this year mitchell received a 600 refund of state income tax. mitchell could have deducted 1100 of state income tax on
If the correltation coefficient has associated probability : 1. if the correltation coefficient has associated probability value of .02 thenthe result is importantthe hypothesis
Complete the table estimate the instantaneous position : a 1600 kg supercar executes a rolling start and accelerates rapidly. the road is horizontal. neglect tire resistance
Prepare the journal entry to record the hale companys : on january 31 hale companys payroll register showed that its employers earned 30320 of office salaries and 82750 of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the power needed to drive the pump if the pump

a feed water pump operates with a flow rate of 350 kgs. the water enters at 420 k. the inlet pressure is 0.7 mpa and

  Evaluate the effect of the water spray on efficiency

Evaluate the effect of the water spray on efficiency (net work out divided by heat input) and net power out per kg/s of dry air coming into the turbine.

  A disk has a mass of 4kg and a radius of 90mm it is at rest

a disk has a mass of 4kg and a radius of 90mm it is at rest when it is placed in contact with the belt which moves with

  Compute the minimum possible radius of the specimen

A circular specimen of MgO is loaded using a three point bending mode. Compute the minimum possible radius of the specimen without fracture, given that the applied load is 5560N, the flexural strength is 165 MPa. and the separation between load po..

  If a particles position is described by the polar

if a particles position is described by the polar coordinates r 2 sin 2u m and u 4t rad where t is in seconds

  Questions on entropy, exergy, cycles, otto cycle

Questions set on  Entropy,  Exergy,  Cycles, Otto Cycle,  Rankine Cycle.  In a coal fired thermal power station, indicate where the exergy contained in the coal is destroyed. For each exergy destruction mechanism, explain whether there is a small..

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

  Due to compressibility of oil the piston retracts 001 inch

the load on a 2 inch diameter hydraulic cylinder increases from 10000lb to 15000lb. due to compressibility of oil the

  You think this is a polytropic compression process write

you are a new engineer at a company that manufactures gas-filled shock absorbers for racing cars. the chief engineer

  Plot data using appropriate dimensionless groups

Assume that viscous effects are negligible Plot this data using appropriate dimensionless groups

  An equimolar mixture of n2 and o2 is heated to 2100 k at 1

an equimolar mixture of n2 and o2 is heated to 2100 k at 1 atm which generates no. calculate the molar values of the

  A 1000kg car is moving horizontally at a constant speed of

a 1000kg car is moving horizontally at a constant speed of 10kmhr on a straight path. what is the absolute minimum

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd