Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Compare the 2's complement and sign-magnitude adders designed above. Estimate the area in terms of number of 1-bit full-adders and additional 2-input logic gates. For performance, use the timing analysis tool provided in the Xilinx Tools as follows: In the Process Window, go to Implement Design ? Map Report ? Timing. Double click on Timing to perform timing analysis on your circuit. A ( v ) near that indicates successful completion of the analysis. Now double click on Timing Report in the submenu to pullup the Timing Report. This report is a textual version of your circuits timing characteristics. It gives the timing paths from (all) inputs to (all) outputs if a path exists between them. Take time to analyze the report generated in the context of the design you completed and determine the worst case delay through your circuit.
A 15 hp, 209V,three-phase,six pole, Y-connected induction motor has the following parameter values per phase: R1= 0.128 ohm, R'2=0.0935 ohm Xeq- X1 + X'2 = 0.49 ohm. The motor slip at full load is 3%, and the efficiency id 90%.
The core is made of cast steel. Find the MMF required to get an air gap flux of 60,000 lines. The cross sectional area of the center section and air gaps is 4 in^2. The remaining sections have a cross sectional of 6 in^2.
a). Develop a function with the name myAMmod to modulate the message signal. Use a carrier frequency fc=200hz. Plot the magnitude spectrum of the message signal and the modulated signal and explain the difference between them.
1. What are some of the fundamental differences between ladder logic programs and relay logic diagrams 2. What are the advantages and disadvantages of a PLC simulation software with virtual input
A discrete-time signal x[n] is periodic with period 8. One period of its DFT harmonic function is {X[0],...,X[7]}={3,4+ j5,- 4 - j3,1+ j5,- 4,1- j5,- 4 + j3,4 - j5}. (a) What is the average value of x[n] (b) What is the signal power of x[n]
An internet access provider (IAP) owns two servers. Each server has a 50% chance of being "down" independently of the other. Fortunately, only one server is necessary to allow the IAP to provide service to its customers
A load impedance ZL = 100 + j80 is to be matched to a 75 ohm line using a single shunt-stub tuner. Find two designs using open-circuited stubs. Include both smith chart and analytical analysis.
How to identify the starting and ending leads of winding in a motor which is having 6 leads in the terminal box.
Design a vending machine controller. The machines sells coke and pepsi. The cost is 25 cents, accepting dimes and nickels. When a dime is inserted the input D is asserted. When a nickel is inserted the input N is asserted.
This document is shown a paper on Orthogonal frequency-division multiplexing with advantages, disadvantages and uses.
A 3-D cubic unit cell contains four atoms whose centers are positional halfway up along each of the vertical cell edges and one atom each centered in the middle of the top and bottom faces.
Design an amplifier circuit to amplify the small output voltage of a transducer of 50mV peak to deliver an output voltage of 8V peak to a 10k ohm load. (This design will produce 1 simulated circuit and an ac output and gain verified using an oscil..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd