Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
the project manager on a development project working on a new line of laptop computers. The project has been broken down into the following modules: Power supply, Processor and motherboard with RAM, I/O circuit board, CD-ROM drive, Floppy drive LCD display, Keypad, Enclosure and all mechanical parts, Final assembly. The total manufacturing cost goal for the project is $500. Develop an initial coast budget for the project that will meet the target manufacturing cost. Use your best estimates of how to divide the amount of the project goal. Does the $500 goal seem reasonable? Would a $250 goal reasonable?
The nickel- cadmium (nicad) battery is a secondary battery, meaning it can be recharged. it has the following reactions occuring during discharge: A nicad battery has .87 g of cadmium, which is the limiting reactant.
1.Convert 5EDA into binary number. What makes base 16 (Hexadecimal) an attractive numbering systems for representing values in computers 2. What is 4365 - 3412 when these values represent unsigned 12-bit octal numbers
Solve the equation z^2+z+1=0 using z=(x,y) and the basic definitions. (Hint: Note that y does not equal 0 because the equation X^2+X+1 does not equal 0 for any real number x.)
Efficiency in a power transformer is 98.6 percent when loaded such that its copper losses are five times its core losses. Calculate the per unit resistance of this transformer.
ManchesterEncodingFSM the clock (Clk_H) will need to run at a speed that is twice as fast as the clock that defines the boundaries of the RawSerialIn_H serial data bit cell this will allow the FSM to resolve or discriminate the middle of each raw ..
What is the frequency of the rotor currents? What is the angular velocity of the stator field with respect to the stator? With respect to the rotor?
What value of emitter resistor would you choose, if: a) You have to amplify the signal of a microphone that has an internal resistance of 100K using a Common Emitter bias configuration b) you have to drive a load of 50 with an Emitter Follower cir..
Two short antennas each of length 10cm at the origin carry identical currents of I = 5 Sin (wt). One is in the az direction and the other one is in the ay direction. If the frequency of the antenna is 60 MHz then calculate
The speed of a 10HP, 230V, 1200 rpm separately excited DC motor is controlled by a 1-phase full-wave bridge converter. The rated armature current of the motor is 10 A. The armature resistance is 0.25 Ohm and the armature inductance is 10 mH.
A square wave signal with voltage levels 0 volts and 2.0 volt at a frequency of 1.00 MHz is multiplied by a sine wave at a frequency of 5.0 MHz
A wave propagates 50m through a dielectric of region 1. Region 1 is lossy. Here, f= 0.6 Np/m. At an interface to region 2, the reflection coefficient is r =0.2+j0.5. The wave then propagates 50m back into region 1 from where it originated.
Suppose that a family of logic gates considers the input ranges of [0 - 0.2V] as "0" and [3.1V-3.5V] as "1". 1. What are the reasonable output ranges for "0" and "1" (a) "0": [0.0 - 0.1V], "1": [3.2V - 3.5V];
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd