Estimate exit temperature of the ethylene glycol solution

Assignment Help Mechanical Engineering
Reference no: EM131498625

Question: A counter flow evaporator based on R-134a refrigerant has been designed with a capacity of 12 tons of refrigeration. The evaporator is used to cool 50 vol% ethylene glycol solution (cp = 0.775 Btu/(lb ?F) that enters the heat exchanger at 55?F with a mass flow rate of 20000 lb/h. The R-134a enters the heat exchanger at 35?F with a quality of 0.1 and leaves with a quality of 0.65. Estimate the exit temperature of the ethylene glycol solution, the mass flow rate of the refrigerant, and the increase in efficiency of the heat exchanger if the surface area of the evaporator were doubled. Further Information: The R-134a refrigerant has experienced a phase change.

Reference no: EM131498625

Questions Cloud

Design heat exchanger that could be used in engineer system : Fuel oils such as #2 fuel oil may be used in boiler burners to provide energy to the working fluid in the boiler tubes. Due to the high viscosity of the fuel.
Possibility of three business computers : With the possibility of three business computers in his home, and all of his business records possibly vulnerable, this would be a good time to advise Bill.
Conduct the appropriate statistical analyses using spss : With your disease in mind, and the instructor feedback you received on your methods section, conduct the appropriate statistical analyses using SPSS and review.
Permanent and temporary storage confused : This week has been all about storage. People often get permanent and temporary storage confused.
Estimate exit temperature of the ethylene glycol solution : A counter flow evaporator based on R-134a refrigerant has been designed with a capacity of 12 tons of refrigeration. The evaporator is used to cool 50 vol%.
What you have learned about state of social capital in us : What you have learned about the state of social capital in the United States? Are we "Bowling Alone" instead of in groups as in decades past?
Risk information sheet for at least five potential risks : Using the sample shown below, create a Risk Information Sheet for at least five potential risks that might be encountered during the conversion.
Calculate the betas and average returns for all stocks : Calculate the Betas and average returns for all stocks and describe their distributions. Test the hypothesis that Alpha on all your regressions is positive
About its profitability index and discounted payback : Suppose a project has conventional cash flows. About its discounted payback? About its profitability index?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd