Each cord for the system to be in equilibrium

Assignment Help Mechanical Engineering
Reference no: EM13713210

If the box weighs 200 lbs, what force must be in each cord for the system to be in equilibrium? Cable AB is 1.5m and the vertical distance from B to A (marked as "y") is 0.75m

Reference no: EM13713210

Questions Cloud

What is the initial velocity of the rock : A rock is thrown vertically up to the air. It reaches a maximum 15 m above the point where it was released. What is the initial velocity.
Importance of structural mechanics in mechanical engineering : Briefly discuss the importance of Structural Mechanics in Mechanical Engineering? List four different types of loadings that can be applied on mechanical structures or components
Find the rms speed of the oxygen molecules in the air : At what Kelvin temperature does the rms speed of the oxygen (O2) molecules in the air near the surface of the earth become equal to the escape speed from the earth
For plain carbon steel and convection : For plain carbon steel and convection (h=50 W/m^2 K) to air at 500K, Ti=300k, with a slab geometry 0.2 m thick (2L), find Boat Number. For a Fourier number (based on l=0.1m) of 0.1, is the tearm series valid? Find the time
Each cord for the system to be in equilibrium : If the box weighs 200 lbs, what force must be in each cord for the system to be in equilibrium? Cable AB is 1.5m and the vertical distance from B to A (marked as "y") is 0.75m
Temperature of the liquid is uniform that only changes time : You like to drink your mixture of coffee and cream very hot. However, it takes you 15 minutes to walk from the coffee house to your office, so you wonder when is best to mix the cream to the coffee. Your favourite mix is half-half, that is, half mug ..
The diameter of largest solid sphere for lumped behavior : For plain carbon steel, with properties at 300K in the Appendix and convection (h=50 W/m^2 K) to air at 500K, determine the diameter of largest solid sphere for lumped behavior (2 part- show equivalent length is D/6 and that D for Bi
How is the terminal velocity impacted : Consider an object falling through air. How is the terminal velocity impacted when certain physical properties are changed, let us define.
What is the average force exerted : A meteor of mass 575 kg has speed 90.0 m/s when it is 800 km above the surface of the Earth. It is falling vertically and strikes a bed of sand. What is the average force exerted by the sand on the meteor

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the fraction of the heat transfer qh discharged

a reversible heat pump cycle operates between hot and cold reservoirs at th 27degc and tc -3degc respectively.

  Gold foil is 008 mm thick and 670mm2 in area a it is cubic

gold foil is 0.08 mm thick and 670mm2 in area. a it is cubic with a0.4076nm. how many unit cells are there in the foil?

  The heat rejection temperature is 70 f for the same

a fossil-fuel steam power plant operates at about 50 of carnot thermal efficiency. it has been suggested that the air

  Explain with clear reference to structural mechanisms and

magneto is seeking to produce a new helmet using a deep drawing process in which a sheet of 3103 aluminum will be

  Elevator starting from rest accelerates

If an elevator starting from rest accelerates at 10m/s and then decelerates at -1m/s until it reaches the top floor (ignore gravitational acceleration, assume g=0. Plot the corresponding a-t, v-t and s-t graphs.

  A mass of gas at an inital pressure of 28 bar

A MASS of gas at an inital pressure of 28 bar and with internal energy of 1500kj,is

  Air is compressed in a steady-flow compressor via a

air is compressed in a steady-flow compressor via a polytropic process from 15 psia and 60ordmf state 1 to 75 psia and

  18 ft3lb of ammonia at 130f is a two-phase liquid-vapor

1.8 ft3lb of ammonia at 130f is a two-phase liquid-vapor mixture. determine the quality of a two-phase liquid mixture

  More heat is transferred until the pressure inside the

a piston-cylinder device with a set of stops on the top initially contains 3 kg of air at 200 kpa and 27 degrees

  Assume isentropic operations for all compressor and the

assume isentropic operations for all compressor and the turbine stages and use constant specific heats at room

  Determine the number of revolution by the disk

a disk has a mass of 4kg and a radius of 90mm, it is at rest when it is placed in contact with the belt, which moves with a constat speed (v =15m/s). knowing that friction is .25 between the disk and the belt. Determine the number of revolution by..

  Draw the shear and bending moment diagrams for the beam

draw the shear and bending moment diagrams for the beam and loading shown and determine the maximum normal stress due

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd