Drive a dc motor without the use of a dac

Assignment Help Mechanical Engineering
Reference no: EM131200102

Typically, when a digital transducer is employed to generate the feedback signal for an analog controller, a digital-to-analog converter (DAC) would be needed to convert the digital output from the transducer into a continuous (analog) signal. Similarly, when a digital controller is used to drive an analog process, a DAC has to be used to convert the digital output from the controller into the analog drive signal. There are ways, however, to eliminate the need for a DAC in these types of situations.

(a) Show how a shaft encoder and a frequency-to-voltage converter can replace an analog tachometer in an analog speed-control loop.

(b) Show how a digital controller with PWM can be employed to drive a dc motor without the use of a DAC.

Reference no: EM131200102

Questions Cloud

When will the efficiency costs of the tax be greater : Suppose that the government of Michconsin imposes a tax on cheese curd production. - When will the efficiency costs of the tax be greater-in the short run or in the long run-and why?
What is the economic order quantity for this item : A product used in a laboratory of the hospital costs $ 60 to order, and its carrying cost per item per week is one cent. Demand for the item is six hundred units weekly. What would be the reorder point for this item if no safety stocks were kept? Wha..
Malware detection and prevention and log management : Discuss three (3) methods of safe computing to help in the prevention of Virus and Trojan attacks.  Present the basic technical knowledge that a layman would need in order to use the methods you identified.
Small boutique honey manufacturer in massachusetts : Will the deadweight loss of this tax be greater, smaller, or the same as if there were no production externality? Explain.
Drive a dc motor without the use of a dac : Show how a shaft encoder and a frequency-to-voltage converter can replace an analog tachometer in an analog speed-control loop.
Advantages or disadvantages between the two : There are two types of hypervisors (bare-metal) and hosted. What are the advantages or disadvantages between the two?
Cost of ordering and carrying for sterilization packages : The CHEMSA chemical supply center provides popular sterilization materials for hospitals. The weekly demand for sterilization materials is two hundred packages. Determine the average number of packages on hand. Determine the number of orders per year..
What kinds of disabilities might an ell have : What kinds of disabilities might an ELL have? What are the challenges of determining whether an ELL has a learning ability or is gifted? What kinds of interventions are used once an ELL has been identified as having a learning disability?
Problem regarding the heuristics and analytics : The ideal method of evaluation products involves volunteers. However, sometimes this is not feasible (i.e., product time constraint, too expensive, etc). This where experts who are knowledgeable about interaction design, needs, and typical behavio..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the power of a pump if 2000 kgmin of water is

determine the power of a pump if 2000 kgmin of water is compressed from 100 kpa to 1 mpa. the water density can be

  Calculate the applied bending moment

Calculate the applied bending moment on a 60 mm x 160 mm rectangular beam with a maximum bending stress of 20,000 kPa.

  Determine the slope and intercept of the line

Enter the data into a spreadsheet. and construct a standard-additions plot of the data.

  Conventional lead-acid automobile battery

The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and maintain at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery). If a batter..

  Find the natural frequencies and mode shapes of the system

A rigid rod of negligible mass and length 2l is pivoted at the middle point and is constrained to move in the vertical plane by springs and masses, as shown in Fig. 5.42. Find the natural frequencies and mode shapes of the system.

  Determine the mass flow rate of fuels in grams per second

determine the mass flow rate of fuels in grams per second from the gasoline tank to the cars fuel injection systems and

  Determine the magnitudes of forces fa and fb acting on each

determine the magnitudes of forces FA and FB acting on each chain and the orientation ? of FB so that the magnitude of FB is a minimum.

  Determine the largest couple that can be transmitted

Prob. 8.110 In the pivoted motor mount shown the weight W of the 175-lb motor is used to maintain tension in the drive belt

  Determine the velocity of the piston

At the instant shown, determine the velocity of the piston, the velocity of the point C and the angular velocity of the connecting rod.

  Calculate the effect on the revenue

Calculate the effect on the revenue received from the express service if theprice of the ordinary bus service is reduced from $75 to $50 whilethe price of the express bus service remains the same.

  Explain what is the output of the fuel cell stack

The reference voltage for a fuel cell at 80°C is Ev= 1.18 V. Assume any losses to be negligible and that the voltage at which it operates is the open circuit voltage; in reality, the voltage would be lower due to the current flow. What is the outp..

  Steam at 95 bar and 400 c is supplied in turbine the

steam at 95 bar and 400 c is supplied in turbine. the condenser pressure is 0.035 bar. if the plant operates as a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd