Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Exercise
For each of the three code segments below, draw the waveform that results on output RB7. If the waveform is repeating, then say so and draw at least two cycles. Also, clearly indicate logic '0' and logic `1' on your waveforms. For all code segments, pin RB7 is connected to RBO as shown in Figure 1 below. Be sure to clearly indicate the initial state of the RB7 output.
Code 1
interrupt isr() {
if (INTOIF) (INTOIF = 0; RB7 = 1;}main() (
TRISB = Ox7F; RB7 = 1;
IPEN = 0; INTEDGO = 0; INTOIF = 0; INTOIE = 1; PEIE = 1; GIE = 1; while (1) {
R87 - 0;
while (IFtB0) ;}
Code 2
interrupt isr() I
if (INTOIF)
INTOIF = 0; RB7 = 1; INTOIE = 0;main() {TRISB = Ox7F; RB7 = 1;IPEN = 0; INTEDGO = 0; INTOIF = 0; INTOIE = 1; PEIE = 1; GIE 1; while (1){RB7 = 0;while(!RBO);}
Code 3
interrupt isr()if (INTOIF) {INTOIF = 0; RB7 = 1;}1main() (TRISB = Ox7F; RB7 = 1;} IPEN = 0; INTEDGO = 1; INTOIF = 0; INTOIE = 1; PEIE = 1; GIE = 1;while (1){ RB7 = 0; while(!RBO);}
Verified Expert
Solution conclusion is presented in the report in both word and pdf format. There were mainly 2 things. Which includes problem statement cum coding, and output waveform.
An n-type piece of silicon with a length of .21um and a cross section area of .05x.05 um sustains a voltage difference of 1V. If the doping level is 10^17 cm^-3, Calculate total current flowing through the device at 300K
a)apply gauss's law to find the total flux leaving the closed surface of the cube. b)evaluate - *D at v the center of the cube. c)estimate the total charge enclosed within the cube.
A DS-SS system requires 40 db of CW rejection of an interfering signal. it uses an 8-stage shift register m-sequence generator and transmits 1.5 kbps binary message data an a 2 GHz carrier. What clock code is required and what is the first null ba..
Explain the statement that induction motor is fundamentally a Transformer?
On a breadboards, hook up an IR LED to provide an infrared light source for signaling the phototransistor as shown in Figure 2 below. Use a pushbutton switch to turn the IR LED on and off.
If I have an AC series circuit with a voltage source of 3 Vrms, a frequency of 5 kHz, a 100 mH coil, and a 1 kohm resistor, how do I determine what the back emf is
Suppose a certain causal signal f(t) has a Laplace transform F(s) = 1. If f(t) is sampled at times kT where T is a constant time interval and integer k>=0, what are the sample values
If the peak-to-peak voltage of a sinusoidal waveform extends vertically 6.4 divisions and the oscilloscope vertical sensitivity was set to 0.5 volts/division, what would be the reading of a multimeter using both the AC and DC scales
The design of a sustainable energy supply system to meet the demands of a small community.
If you have a purely inductive load with a reactance of 2/377 O connected to the 120Vrms 60 Hz (i.e., f = 377 rad/sec) AC line, what value of capacitor (in Farads) must be put in parallel with it to set the power factor to one
A 150-MVA 15/200-kV single-phase power transformer has a 0.018ohm resistance and a 0.075ohm reactance. The magnetizing impedance is j80 per unit. a.) Find the equivalent circuit referred to the low-voltage side of this transformer.
The wave reflects from the speeder's car and returns to the police car, where its frequency is measured to be 322 Hz less than the emitted frequency. Calculate the speeder's speed with respect to the ground.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd