Draw elevation view of the beam showing the stirrup layout

Assignment Help Mechanical Engineering
Reference no: EM131169171

The simply supported beam shown is on a clear span of 30 ft. The beam carries uniformly distributed service loads of 1.9 kips/ft live load and 0.7 kip/ft dead load (excluding the weight of the beam). Additionally, the beam carries two concentrated service loads of 8 kips dead load each, one load being placed 5 ft in from the face of each support. The beam is reinforced with No. 3 single-loop stirrups placed in the following pattern, starting at the face of the support (symmetry about mid span): one space at 2 in., five spaces at 8 in., four spaces at 10 in., and eight spaces at 12 in. Beam width b = 15 in., h = 28 in., and d = 25.4 in. Use f′ c = 4000 psi and fy = 60,000 psi.

1330_The Simply Supported Beam.jpg

a. Draw an elevation view of the beam showing the stirrup layout.

b. Draw the Vu diagram.

c. Calculate ∅(V+ Vs) for each spacing group (omit the 2-in. spacing).

d. Superimpose the results from part (c) on the Vu diagram and comment on the results.

Reference no: EM131169171

Questions Cloud

Define the term principal-agent problem : 1) Define the term principal-agent problem. What principal-agent problems exist in a market? What principal-agent problems exist in a firm? What are possible solutions to principal-agent issues within the firm?
Find the radius and height of a container : Find the radius and height of a container if it has a capacity of 36 in.3 and is constructed using the least amount of metal.
Health products on the market : Near the end of the video clip, the health and medical editor states that washing hands and drinking water will keep one healthier than most of the health products on the market.
Vitamin water responds to the claim : Vitamin Water responds to the claim by stating that the ingredients are clearly on the label. Discuss whether manufacturers have any duty to warn the public about their products or whether the law should adopt the idea of "buyer beware" so that c..
Draw elevation view of the beam showing the stirrup layout : Draw an elevation view of the beam showing the stirrup layout. Draw the Vu diagram. Calculate ∅(Vc + Vs) for each spacing group (omit the 2-in. spacing). Superimpose the results from part (c) on the Vu diagram and comment on the results.
What is the volume of such a package : Find the dimensions of a rectangular package that has a square cross section and the largest volume that may be sent via priority mail. What is the volume of such a package? Hint: The length plus the girth is 4x + h (see the accompanying figure).
Deceptive advertising or mere promotion : According to the video, Coca Cola advertises that Vitamin Water will give people protection similar to exercise or flu shots. Discuss whether this is deceptive advertising or mere promotion.
What happens when you slowly pulled the cardboard : What happens when you slowly pulled the cardboard? Explain, What happens when you flicked the cardboard? Explain and What happens when you hit the coin at the bottom? Explain
What are the six barriers to affective planning : What are the six barriers to affective planning? How does each interfere with effective planning?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd