Draw appropriate control scheme using simplified isa symbols

Assignment Help Electrical Engineering
Reference no: EM13268688

Wastewater leaving the ACME cheese factory must be neutralized to a pH between 6.8 and 7.2. Citric acid is available to decrease pH and sodium hydroxide is used to increase pH. The neutralization occurs on-line in the discharge piping by addition of acid or base as required based on upstream pH measurement. draw an appropriate control scheme using the simplified ISA symbols.

Reference no: EM13268688

Questions Cloud

Calculate and write same file total of yesterdays receipts : A parking garage charges a $ 5.00 minimum fee to park for up to three hours and an additional $ 1.00 per hour for each hour over the hours. the maximum charge for any given 24 hours period is $ 2.00.
What is the mass in grams of the cup : A 23 g ice cube at -4.6 oC is place in an aluminum cup whose initial temperature is 80.56 oC. What is the mass in grams of the cup
Calculate the phase impedance of the transformer in per unit : A 50-KVA, 13,800/208 V ?-Y distribution transformer has an equivalent phase impedance 114.2+j800 ohm referred to the high voltage side. Take the rated voltage as the base voltage and the rated VA as the based voltampere value.
Determine the angular size of the moon : the moon has an angular size of .5degrees when viewed with unaided vision from earth. what is the angular size of the moon as seen through this telescope
Draw appropriate control scheme using simplified isa symbols : Wastewater leaving the ACME cheese factory must be neutralized to a pH between 6.8 and 7.2. Citric acid is available to decrease pH and sodium hydroxide is used to increase pH.
Predict the effect of doubling the reactant concentration : In any chemical fabrication process (eg. wet etching or CVD) there are two main regions where the reaction rate is dominated by different processes. Name them and explain what each of those regions mean.
Find dimension of window after ideal isotropic etching : A set of 4 µm wide windows are to be etched into a SiO2 film of thickness 0.8µm. a) Find the dimension of the window, as measured at the top of the oxide, after ideal isotropic etching (i.e. no overetch).
Discussion post excluding formal citation : What are the merits of each argument and which side do you support and why? How does the use of capital punishment in Texas compare to other states?
Find n that probability of detecting at least one defective : From a large lot of new tires, n tires are to be sampled by a potential buyer, and the number of defectives X is to be observed. If at least one defective is observed in the sample of n tires, the entire lot is to be rejected by the potential buye..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine vaulters altitude as vaulter crosses the bar

A 52-kg pole vaulter running at 12 m/s vaults over the bar. Her speed when she is above the bar is 0.7 m/s. Neglect air resistance, as well as any energy absorbed by the pole, and determine her altitude as she crosses the bar.

  Determine equivalent circuit referred to high-voltage side

150 kVA, 2400/240 V single-phase transformer has the parameters. (a) Determine the equivalent circuit referred to the high-voltage side. (b) Find the primary voltage and voltage regulation when transformer is operating

  Describe as best as possible an automatic garage door opener

discuss to describe as best as possible an automatic garage door opener system. You should either use one you are familiar with as an example, or recall the details from one or more that you imagine could be available

  Calculate what is magnitude terminal voltage at power system

Through a three-phase transmission line, a three phase symmetrical load is supplied from a power system bus. The parameters per phase of the transmission line are: R=5 ohms, X=70 ohms, B=9*10^-4 ohms.

  Calculate the power dissipated in the device

An InP TED is 0.5 pm long with a cross sectional area of 10" cm2 and is operated in the transit-time mode.(a) Find the minimum electron density no required for transit-time mode.

  Find the transformation ratio of a transformer

Find the transformation ratio of a transformer having 350 turns on the secondary winding and 7000 turns on the primary. What voltage must be applied to the primary of the transformer to develop an open-circuit secondary voltage

  Determine velocity and acceleration of a with respect to b

At the instant shown, car A has a speed of 20km/h, which isbeing increased at a rate of 300km/h2 as the car entersan expressway. At the same instant, car B is decelerating at250 km/h2 while traveling forward at 100 km/h.

  Determine the required user signal power to achieve ber

In a multiuser CDMA system of DSSS, all transmitters are at equal distances from the receivers. The additive white Gaussian noise density Sn(f) = 5x10^-7 W/Hz. BPSK is used by all users with bit rate = 16 kb/s. There are 16 users.

  Discuss what steps operator can take to reduce instability

The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car.

  What is value of g at an altitude of 20 miles in unites

g0 is the acceleration of gravity at the surface of the Earth, A is the altitude, and Re is the radius of the Earth, approximately 6,380 kilometers. What is the value of g at an altitude of 20 miles in unites of meters per second squared

  What is the maximum frequency that an input

An OpAMP has a unity gain frequency (ft) of 10MHz and a slew rate of 10V/us and AVoc = 120dB at DC (f=0).  Assume VCC = -VEE = 15 Volts.a. Approximate the cutoff frequency of the OPAMP itself. b.

  Determine what is the value of n of a wire

Due to the current, the temperature of the wire is raised by T in atime t. A number N of similar cells is now connected in series with a wire of the samematerial and cross-section but of length 2L.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd