Draw a block diagram of the system

Assignment Help Electrical Engineering
Reference no: EM131091645

Consider the liquid-level control system shown in Figure 4-43. The controller is of the proportional type. The set point of the controller is fixed. Draw a block diagram of the system, assuming that changes in the variables are small. Obtain the transfer function between the level of the second tank and the disturbance input qd. Obtain the steady-state error when the disturbance qd is a unit-step function.

Figure 4-43

1984_8b7bf316-f802-45eb-bef3-73031d41d711.png

Reference no: EM131091645

Questions Cloud

Figure obtained likely to be a realistic estimate : Cohn and Sitwell, Inc., is considering manufacturing special drill bits and other equipment for oil rigs. The proposed project is currently regarded as complementary to its other lines of business, and the company has certain expertise by virtue o..
Develop understanding of business and competitive strategies : MBA 521 -Conduct secondary research (i.e. library, internet, etc) and write research paper computing the financial ratios yourself - Develop an understanding of the business and competitive strategies of the company.
Identify where strategic principles of consensus organizing : What did you learn about the strategic principles from this case study? What questions do you still have about the strategic principles? How difficult or easy would it be to implement these principles?
Determine the time constants of the combined thermocouple : Determine the time constants of the combined thermocouple-thermal-well system Assume that the weight of the thermocouple is 8 g and the weight of the thermal well is 40g. Assume also that the specific heats of the thermocouple and thermal well are..
Draw a block diagram of the system : Obtain the steady-state error when the disturbance qd is a unit-step function.
The following capital structure : 1. Company A has beta of 1.7, debt/assets ratio of 20%, a tax rate of 34%, a cost of debt of 9%, and a cost of equity of 15%. The riskless rate is 4%. Find the WACC of Company A.
Write a report on The current state of Airline Industry : Write a four page report about The current state of Airline Industry. explain the economical factors and its global influence and performance in 2014. Provide an example of airline industry and perform the SWOT Analysis. Also describe the role of the..
What kind of control action does this controller produce : The pneumatic relay has the characteristic that pc=KPb, where K > 0. What kind of control action does this controller produce
Are good people actually invulnerable to harm : What does Socrates mean when he says in the Apology that "no evil can happen to a good man, either in life or after death" (41d)? Another translation says "a good man cannot be harmed in life or death". According to Plato's view, in what sense is ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the extreme values of the output voltage

A differential amplifier has a bias current of 100 n A, a maximum offset current of 20 n A, a maximum offset voltage of 2 mV, an input resistance of 1 MΩ, and a differential gain of 1000. The input terminals are tied to ground through (exactly equ..

  Determine the value of x and xc at resonance

The cutoff frequencies of a series resonant circuit are 5400 Hz and 6000 Hz. a. Find the bandwidth of the circuit. b. If Qs is 9.5, find the resonant frequency of the circuit. c. If the resistance of the circuit is 2-ohm, find the value of X and XC a..

  Calculate the new armature current and power factor

A 208-V Y connected three phase synchronous motor has a synchronous reactance of 4O per phase and negligible armature winding resistance. At a certain load the motor take 7.2kW at 0.8 pf lagging.

  Explain how to design the base-emitter area of npn bjt

Design the base-emitter area of NPN BJT so that its transconductance gain is gm=2 A/V at VBE=0.70 V. The technological parameters are as folows: the emitter is heavily doped, the base doping is 5*1017cm-3,the base width is W=0.5μm

  Bending stress of a rectangular plate

When calculating the bending stress of a rectangular plate, one must use the section modulus about the neutral axis of the plate. This axis is at the center of the plate where there is neither tension nor compression.

  Determine the voltage across the capacitor at time t

At t=40s, the capacitor is disconnected from the charging circuit and connected in parallel with a 5- Mega ohm resistor. Determine the voltage across the capacitor at t=40s and at t=100s.

  Determine the net charge that passes through the element

The current through a particular circuit element is given by i(t) = 10sin(200*pi*t) A. Determine the net charge that passes through the element between t=0 and t=10ms. Repeat for the interval t=0 and t=15ms.

  Find the current-i through the light bulbs

Three light bulbs are connected in series to a 100-V battery in a circuit. Each light bulb dissipates 30W, 40W, and 50W, Respectively. Find the current (I) through the light bulbs.

  Find a minimal sum-of-products expression for each function

Given a sum-of-products expression, it is possible to write the 1s corresponding to each product term directly on the map without developing an explicit truth table of minterm list, and then proceed with map minimization procedure.

  Design a wafer structure for the laser

Graded-index separate confinement double heterostructure (GRIN-SCH) InGaAs/GaAs lasers with various cavity lengths were tested in the lab. The 100m wide oxide strip lasers consists of two pairs of 10nm In0.2Ga0.8As quantum-well (QW).

  Sketch the circuit needed to implement the counter

a binary pulse counter can be constructed by inter connecting t-typeflip-flops in an appropriate manner. assume it is desired toconstruct a counter which can count up to 100 subscript 10. A) how many flip flops are required

  Find value of w0 for which amplitude of current is max

Compute i2(t) through resist R, Find value of w0 for which the amplitude of the current |I2| is maximum, compute I2 for w=w0. Does I2 depend on R is there a contradiction with ohm's law

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd