Double the pressure of the gas inside the cylinder

Assignment Help Mechanical Engineering
Reference no: EM13706606

A vertical piston-cylinder device contains a gas at a pressure of 100 kPa. The piston has a mass of 5 kg and a diameter of 12 cm. Pressure of the gas is to be increased by placing some weights on the piston. Determine the local atmospheric pressure and the mass of the weights that will double the pressure of the gas inside the cylinder.

Reference no: EM13706606

Questions Cloud

Force and its location on the cork due to saltwater : A small, narrow, flat-bottomed fishing boat is loaded down with two crew member and a catch fish. The rear of the boat is a plane inclined at an angle θ of 75 degrees with the horizontal. Thirty centimetres below the water surface is a hole in the b..
Determine the final pressure and temperature in the tank : A closed rigid tank of volume 3m^3 contains a two-phase liquid-vapor mixture of H2O at 110C with a quality of 34.5%. The tank then receives energy by heat transfer until the water becomes a saturated vapor. Determine the final pressure and temperatur..
What is its temperature and quality : R134a rests in a compressed fluid can at 120psia, and a specific volume of 0.38ft3/lbm. What is its temperature and quality? Half of the mass is now vented off to the atmosphere. The can is allowed to exchange heat with the surroundings at 100°F unt..
Idealized reservoir contains an ideal gas at a pressure : An idealized reservoir contains an ideal gas at a pressure of 4410 psia and a temperature of 91degrees C. Under these conditions the volume of this gas in the reservoir is 10^9 ft^3. What would be the volume of this gas at standard temperature and co..
Double the pressure of the gas inside the cylinder : A vertical piston-cylinder device contains a gas at a pressure of 100 kPa. The piston has a mass of 5 kg and a diameter of 12 cm. Pressure of the gas is to be increased by placing some weights on the piston. Determine the local atmospheric pressure a..
The electricity consumption : The electricity consumption in the USA in 2009 was about 44% of the total energy consumption. Of that about 20% was produced by Nuclear Power Plants. Currently there are 104 Nuclear Power Plants operating in the country. What is the average capacity ..
What is the density of the unknown liquid : Two pipes containing air are connected with two manometers, as shown in the figure. One manometer contains glycerine, and the difference in liquid levels is 10 cm. The other manometer contains an unknown fluid, and it shows a difference in liquid lev..
Rectangular gate is used as a retaining wall : A rectangular gate is used as a retaining wall for seawater as shown in the figure. The gate is hinge at point O 1 m from the bottom. Determine the depth of seawater required for the resultant force to be located at the hinge. The gate width into the..
Advanced engineering thermodynamics by began : Decide one by one the exact location of the points that appear in the two dimensional plot of fig 2.8. How many different paths can the system follow from state a to state b (chapter 2, advanced engineering thermodynamics by began)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the normal stress

If the bar is subjected to centric forces of magnitude P = 30 kN and knowing that EA = 70 GPa and EB = 105 GPa, determine the normal stress (a) in the aluminum layers, (b) in the brass layer.

  If the compressor consumes 400 w of power and the cop the

refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at

  What is the yield strength

If the critical resolved shear stress is 10 MPa, what is the yield strength?

  Fluid is moving between two plates the top plate

Fluid is moving between two plates the top plate is moving with a velocity V, the distance between the plates is h, and the flow is completely horizontal; select the appropriate boundary condition of the viscous flow.

  Which is made of an aluminum pin of unknown diameter

A steel bar AC of length 6in and a varying cross-section is loaded as shown in fig 1. The bar is supported by a pin joint at A. which is made of an aluminum pin of unknown diameter.

  An air tank with a volume of 20m3 is pressurized to 10 mpa

an air tank with a volume of 20m3 is pressurized to 10 mpa. the tank eventually reaches room temperature of 25 degree

  Determine the minimum mass flow rate kgs of the water so

a liquid sodium flowing a 100 kgs enters a heat exchanger at 450 c and exits at 350 c. the specific heat of sodium is

  Steam at 3 mpa and 400 degc is expanded to 30 kpa in an

steam at 3 mpa and 400 degc is expanded to 30 kpa in an adiabatic turbine with an isentropic efficiency of 92 percent.

  A piston-cylinder device containing argon gas undergoes an

a piston-cylinder device containing argon gas undergoes an isothermal process at 100 c during which the pressure

  Define the torsion moment

Calculate spring coefficient k = P/δ and discuss the design on how much spring radius r should be changed to increase k two times

  Determine the maximum stress and the maximum shearing stress

Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum stress and the maximum shearing stress at point L.

  If the parameters are the depth d of the friction layer the

consider the case of a knife whose leading edge is the z-axis and the blade covers the half plane defined by x 0.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd