Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
One of the early creationist theories advanced in opposition to Darwin's theory of natural selection was put forward by the nineteenth-century naturalist Philip Gosse. According to this theory, God created the world in about 4000 b.c., and he did so in exactly six days, per the account in Genesis. To reconcile this story with indications that the world is much older, Gosse argued that God created the world with the appearance of a history. Adam was created with a navel, trees were created with rings, and fossils were implanted in geologic formations and in sea beds. Is Gosse's theory plausible? Does his theory make God out to be a deceiver? Is a world with a fake history intrinsically better than one with no history? If we were to update Gosse's theory, we would have to add that God created the world complete with light rays that appear to have been emitted by distant galaxies more than 10 billion years ago, as well as with fossils having ratios of carbon-12 to carbon-14 that indicate (by carbon-dating techniques) the fossils are millions of years old. Given these provisions, is there any way of disproving Gosse's theory? In other words, is the theory disconfirmable? If not, does this fact make the theory unscientific?
a pot containing 1.0 liters of water at 20 degc is placed on the stove and heat is added to the water at a rate of 500
The following suspension system has two support structures-a spring and a rubber pad. Vertical force F (N) acts on the moveable plate. The spring has a spring constant of k1 = 1000 N/m. The rubber pad has a spring constant of k2 = 20000 N/m. The rubb..
Describe in detail (using appropriate diagrams/drawings) a common accepted method (experiment) you would use to obtain an accurate assessment of the vessel's initial GM
A large manufacturing space with an average floor to ceiling height of 30 ft has a floor area of 5000 ft^2. The total infiltration rate for the space is estimated to be 1.5 air changes per hour. The inside design temperature and relative humidity are..
For a certain system, the first excited state lies 1 eV above the ground state. Is the system degenerate at room temperature? At 106 K?
An elevator descends from rest with an acceleration of 5 ft>s2 until it achieves a velocity of 15 ft>s. Determine the time required and the distance traveled.
A rigid tank of 1 m3 contains nitrogen gas at 600 kPa, 400 K. By mistake someone lets 0.5 kg flow out. If the final temperature is 375 K what is then the final pressure?
a train enters a curved horizontal section of track at a speed of 100kmh and slows down with constant deceleration to
Evaluate the integral obtained in Part (a) using computer software such as Mathematica, Maple, etc. Express your answer in terms of the mass m of the object.
a piston held by a pin in an insulated cylinder shown in figure above right contains 2 kg water at 100c quality 98. the
Steam enters an adiabatic turbine at 5 MPa, 650°C, and 80 m/s and leaves at 50 kPa, 150°C, and 140 m/s. If the power output of the turbine is 8 MW, determine (a) the mass flow rate of the steam flowing through the turbine and (b) the isentropic effic..
A solid is deformed under plane-strain conditions (εz = 0). The strains in the x-y plane are εx = 0.010, εy = 0.005, and γ xy = 0.007. A. Sketch the Mohr's strain circle diagram.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd