Distillery uses mechanical vapour re-compression

Assignment Help Mechanical Engineering
Reference no: EM13701059

The wash still in a whisky distillery uses mechanical vapour re-compression as shown in the simplified diagram of the Figure shown below. The vapour from the still is at 80° C. Take a minimum temperature difference between the vapour leaving the still and the steam in the heat exchanger of about 20 K, and a minimum temperature difference between the steam in the coil and the liquid in the still also of about 20 K. Assuming a compressor isentropic efficiency of 0.65, and a combined mechanical and electrical transmission efficiency for the compressor motor of 0.9, choose suitable pressures for the steam circuit and calculate the COP of the heat pump.

Reference no: EM13701059

Questions Cloud

Low-speed wind tunnel with atmospheric air : A fan that can provide air speeds up to 50 m/s is to be used in a low-speed wind tunnel with atmospheric air at 25°C. If one wishes to use the wind tunnel to study flat-plate boundary layer behaviour up to Reynolds numbers of Rex = 10^8 , what is the..
Where the hydrodynamic boundary layers meet : Air at 20°C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance where the hydrodynamic boundary layers meet.
What is the equation for the actual air temperature : An electric heater heats air. The temperature sensor has a time constant of 5 seconds. The air temperature output (in °C), as measured by the temperature probe is: T=200+cos(0.5t)
Force required to keep the cart moving at constant velocity : A 2 cm horizontal jet of water with a velocity of 15 m/s is spraying onto a vertical plate attached to a cart moving opposite the direction of the water jet at 8 m/s. Determine the force required to keep the cart moving at a constant velocity.
Distillery uses mechanical vapour re-compression : The wash still in a whisky distillery uses mechanical vapour re-compression as shown in the simplified diagram of the Figure shown below. The vapour from the still is at 80° C. Take a minimum temperature difference between the vapour leaving the stil..
Provide a theoretical analysis and treatment recommendation : Case Study Development and Theoretical Explanation - Provided a theoretical analysis and treatment recommendation for the case. The treatment selected flows logically from the theory utilized.
What tax basis does samson take in the devon net assets : What tax basis does Samson take in the Devon net assets and how does Devon use Section 337 to create a nonrecognition gain transaction when Devon transfers appreciated assets to Samson.
Analyse the current financial state of anthonys orchard : Analyse the current financial state of Anthony's Orchard and evaluate the impact of a major customer cancelling their expected order.
Compute the unit sales price to earn budgeted target profit : Compute the unit sales price at which Blake must sell its product in the current year in order to earn a budgeted target profit of £200,000.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd