Discuss steady load flow control method of dc transmission

Assignment Help Electrical Engineering
Reference no: EM131367358

1. Distinguish trigger delay angle, phase-shifter angle, extinguish angle, trigger lead angle, and extinguish lead angle, paying attention to their operating areas.

2. Discuss the steady load flow control method of DC transmission.

3. Compare load flow calculation models with and without DC transmission lines.

4. Give an appropriate value L, C, and draw the curve of SVC equivalent reactance XSVC-b denoted in (5.121).

Reference no: EM131367358

Questions Cloud

Discuss the capacitive and inductive value range of xtcsc : Discuss the capacitive and inductive value range of XTCSC when conduction angle b should avoid the resonance region according to (5.153)-(5.155). Then discuss whether line transmission active power Pc= Plp controlled by TCSC can vary continuously
How to efficiently evaluate the polynomial : How many multiplications are used in your algorithm - Do all your calculations using truncation at the 4th decimal place as shown in Lecture 3. Repeat this using round-off in the 4th decimal place. Compare your results to the calculator result.
Which two of the above phases are the most important : The textbook states that an iterative design process based on the Rosson and Carroll (2002) definition of operational characteristics would consist of four distinct phases:Requirements analysis phase,Preliminary and detailed design phase,Build and ..
Strategic alignment model-five forces model : Describe the model in detail, including how it was originated. Explain how this model has been used and at what stages it was used in IT strategy design and/or implementation. How can the model identify IT management deficiencies?
Discuss steady load flow control method of dc transmission : Distinguish trigger delay angle, phase-shifter angle, extinguish angle, trigger lead angle, and extinguish lead angle, paying attention to their operating areas.
Internal change champion in organization : This should reflect your personal model of being an internal change champion in an organization. This is to be written in the first person. You should apply key intervention models that would be effective in an organization that you well know. Thi..
4p of marketing-the marketing mix : Your first Assignment was based on a scenario. You will now use this same scenario to address the 4 P's involved. Wherever you work you can apply these 4 P's concepts for a better understanding of the product or service provided by the organizatio..
Why can dc transmission lines only transmit active power : Why can DC transmission lines only transmit active power, but the converters absorb reactive power from the AC system?
Describe one neurodevelopmental disorder : Write a 1,500- to 1,750-word paper on the following: Describe one neurodevelopmental disorder and one neurocognitive disorder. Discuss behavioral criteria for each disorder

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Create a multisim schematic of each of designs

Create a MultiSIM schematic of each of your designs. Provide a screenshot. Perform a simulation of each design to demonstrate the filter behavior. Take a screenshot. From your simulation and screenshot in the above step, what is the gain in dB at t..

  Explain the construction & operation of an n- and p-channel

Explain the construction & operation of an n- and P-channel MOSFET in enhancement and depletion modes with the help of static drain characteristics and transfer characteristics?

  Coefficient of kinetic friction

In the system shown below Block A has a mass of 15kg and Block B has mass 5k2. It is measured that the tension in the cable is 40N. Determine the acceleration of Block A and the coefficient of kinetic friction between Block A and the ground (negle..

  Do you think h.323 is actually the same as sip

In Internet telephony, explain how a call from Alice can be directed to Bob when he could be either in his office or at home?

  A manufacturer specification sheet lists the transfer

a manufacturer specification sheet lists the transfer function of a pressure sensor as 45plusmn5 mvkpa with a time

  Write a paper on the impact of electric power engineering

Write a paper on the impact of electric power engineering on ethics and professional practice in electric power engineering. It must be 2- 3pages and in IEEE format.

  Define waste materials generally then divided

Define Waste materials Generally then divided into two groups with their definitions (Hazardous and Non-Hazardous )waste materials, Then explain Fly ash and Slag(GGBFS) Considered as which type ??

  Plots of singular values and indicate on plots the bandwidth

Singular values and associated directions vary with frequency.- Give typical frequency response.- Plots of singular values and indicate on the plots the bandwidth (fBW).

  Determine the annual cost of energy

The maximum demand charge is $30 per kVA per annum, and the energy charge per kWh is 4 cents.

  What is the smallest possible load resistor that can be used

Design a 7.5V zener regulator circuit using a 7.5V zener specified at 12mA. The zener has an incremental resistance of r and a knee current of 0.5mA. The regulator operates from a 10V supply and has a 1.2k-ohm load.

  What is the maximum allowable power drain

what is the maximum allowable power drain in the above example?

  Find what is lightbulbs design life in days

A 60-watt outdoor lightbulb is advertised as having an average life (i.e. MTTF) of 1,000 operating hours. However, experience has shown that it will also fail on demand an average of once every 120 cycles.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd