Discharges heat to the atmosphere 20degc for operation at

Assignment Help Mechanical Engineering
Reference no: EM13629926

A solar collector receives solar radiation at a rate of 0.315 kW per m2 and delivers the heat to a storage unit whose temperature remains a constant 500 K. A power cycle receives heat from the storage unit, generates electricity at the rate of 570 kW and discharges heat to the atmosphere (20°C). For operation at steady state, calculate the theoretical minimum solar collector area required.

Reference no: EM13629926

Questions Cloud

A wind tunnel made of circular duct consists of a : a wind tunnel made of circular duct consists of a contracting nozzle a test section in which experiments are conducted
A researcher reports that there is no consistent : a researcher reports that there is no consistent relationship between grade point average and the number of hours spent
Determine the weight and cost of prepeg required to produce : determine the weight and cost of prepeg required to produce a hollow composite tube outside diameter 50mm wall
A rigid well insulated container with a volume of 2 ft3 : a rigid well insulated container with a volume of 2 ft3 holds 0.12 lb of ammonia initially at a pressure of 20 lbfin2.
Discharges heat to the atmosphere 20degc for operation at : a solar collector receives solar radiation at a rate of 0.315 kw per m2 and delivers the heat to a storage unit whose
An airplane heading eastward is observed to be in a : an airplane heading eastward is observed to be in a 20degree climb at a speed of 1200kmh. at this instant its
The value of the pearson r : the value of the pearson r indicatesa the strength of a linear relationship between two sets of ordinal data.b the
A bullet of mass 81gm and moving with a velocity of 300msec : a bullet of mass 81gm and moving with a velocity of 300msec is fired into a log of wood and it penetrates to a depth of
Which of the following correlations expresses the strongest : which of the following correlations expresses the strongest relationship?a .50b .80c .00d - .35e -

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Water flows 2m deep at 2ms in a rectangular channel find

water flows 2m deep at 2ms in a rectangular channel. find the change in depth and in water surface elevation caused by

  A cast- iron cylinder of 300mm bore carries a pressure of

a cast- iron cylinder of 300mm bore carries a pressure of 30 newtons per square millimitrewhat should be its thickness

  The cylinder from a supply line until all the liquid in the

an insulated vertical piston-cylinder device initially contains 11.56 kg of water 6.94 kg of which is in vapor phase.

  Determine the speed va and angle ua at which the ball was

it is observed that the time for the ball to strike the ground at b is 2.5 s. determine the speed va and angle ua at

  If the body has a forward speed of 2 insec and its position

a retarding force is applied to a body moving in a straight line so that during an interval of its motion its speed u

  What is the theoretical mechanical advantage obtained by

1 a barrel is rolled up an incline 20 ft along its length and 6 ft in vertical height by means of a rope that is

  Using cv constant theory an using thermal properties at

in a diesel cycle the cutoff ratio is two and the compression ratio is eighteen. at state 1 the air is 14.7 psia and

  Find reciprocal lattice of the body-centred cubic structure

What is the minimum energy in the conduction band, and where can it be found in the Brillouin zone?

  If half of these are coal-fired how many tons of coal will

the average electrical generating capacity of the united states was about 475000 mw in 2007. if trends continue this

  If the pressure distribution over the surface of the body

consider a body of arbitrary shape. if the pressure distribution over the surface of the body is constant e.g.

  A molten mixture of salt nano3-kno3 is used as the heat

a molten mixture of salt nano3-kno3 is used as the heat transfer fluid for application in a parabolic trough solar

  Evaluate the work required and the heat transfer

Kinetic and potential energy effects can be ignored. Evaluate the work required and the heat transfer, each in kW.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd