User Account

All Pages

Difference between upper limit and lower limit of dimension

Assignment Help Mechanical Engineering
Reference no: EM131224189

Tolerance:It is the difference between upper limit and lower limit of the dimensions of a part. So, it can be stated as maximum possible variation in the dimension of the part.The tolerance may be applied unilaterally or bilaterally

Reference no: EM131224189

Questions Cloud

Implement a basic initial ner classifier : COMP9318 (16S2) PROJECT - you will use scikit-learn and python 3 to engineer an effective clas- sifier for an important Information Extraction task called Named Entity Recognition and
About to launch social networking site : Imagine that you are about to launch a social networking site. Determine the target market to which your social media site will cater. Recommend a marketing strategy to entice your chosen target market to join your site. Determine the approach you wi..
Independent and establishing own free-standing service : Imagine that you are a credentialed, licensed professional, and that you are considering going independent and establishing your own free-standing service (perhaps an urgent care center, a physical therapy service, a private laboratory, or other s..
Explain how you might mitigate these threats : Using the hypotheses you have developed, compare the characteristics of the different experimental research designs discussed in the Skidmore (2008) article and choose the one that is most appropriate to adequately test your hypotheses. Identify p..
Difference between upper limit and lower limit of dimension : Tolerance:It is the difference between upper limit and lower limit of the dimensions of a part. So, it can be stated as maximum possible variation in the dimension of the part.The tolerance may be applied unilaterally or bilaterally
Influence public policy and gun control : Discuss the strengths and weaknesses of your group and explain how these will affect the methods by which you try to influence public policy and gun control.
Criteria of what he called universalizability : As Kant laid out the criteria of what he called universalizability, he invited us to move into:
Development of job descriptions and job specifications : How might you involve customers in the development of job descriptions and job specifications? Are there any constraints on what customers can stipulate in job specifications?
Which of these is not a level of ethical maturity : Which of these is not a level of ethical maturity?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the total heat lost by the pipe per unit length

A horizontal steel pipe having a diameter of 5 cm is maintained at a temperature of 50oC in a large room where the air (h = 6.5 W/m2.oC) and wall temperature are at 20oC. The surface emissivity of the steel may be taken as 0.8. Calculate the total he..

  Derive an algebraic expression for the temperature of blood

blood at 37degc enters the left ventricle lv of a skier at a rate of 100 mls. at time t 0 the skier steps outside and

  A heat pump with a coefficient of performance of 35

a heat pump with a coefficient of performance of 3.5 provides energy at an average rate of 70000 kjh to maintain a

  Compute the required pressure in the oil

A hydraulic cylinder must be able to exert a force of 38.8 kN. The piston diameter is 40 mm. Compute the required pressure in the oil.

  Problem a 5x5 plate with a crack size of 2a15 is under a

problem a 5x5 plate with a crack size of 2a1.5 is under a spectrum load as shown below. the plate has a yield strength

  Aircraft is propelled by a reversible gas turbine engine

An aircraft is propelled by a reversible gas turbine engine, or turbojet. It is flying at an altitude of 30,000 ft where temperature is -20oF and pressure is 2000 psfa. The compressor has a pressurization ratio p2/p1 of 16 and the kerosene fuel in th..

  A body is acted upon by an upward force of 12n and a

a body is acted upon by an upward force of 12n and a horizontal force of 20n to the right. what are the amount and the

  Determine the volume of the tank

Determine a) the volume of the tank,b)the final temperature and pressure, and c) the internal energychange of the water.

  Draw a schematic of this cycle and number all your points

steam enters the first turbine stage of a vapor power cycle with reheat and regeneration at 32 mpa 600degc and expands

  General wheatstone bridge and derive the output equation

Draw a general Wheatstone bridge and derive the output equation for a bridge comprising 3 resistors of equal value with one resistor changing an amount delta R?

  A rankine cycle operating with ammonia is heated by some

a rankine cycle operating with ammonia is heated by some low temperature source so the highest t is 120oc at a pressure

  Find the heat transfer rate during the process

Nitrogen enters a nozzle steadily at 1.2mpa and 600k with a velocity of 30m/s the inlet area of the nozzle is 0.005m^2 the nitrogen leaves the nozzle at 298k with a velocity if 400m/s. find the heat transfer rate during the process?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd