Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The temperature of flue gases flowing through the large stack of a boiler is measured by means of a thermocouple enclosed within a cylindrical tube as shown. The tube axis is oriented normal to the gas flow, and the thermocouple senses a temperature T, corresponding to that of the tube surface. The gas flow rate and temperature are designated as mg and Tg, respectively, and the gas flow may be assumed to be fully developed. The stack is fabricated from sheet metal that is at a uniform temperature Ts and is exposed to ambient air at Toc and large surroundings at Tsur. The convection coefficient associated with the outer surface of the duct is designated as ho, while those associated with the inner surface of the duct and the tube surface are designated as hi and hi respectively. The tube and duct surface emissivities are designated as e and es respectively.
(a) Neglecting conduction losses along the thermocouple tube develop an analysis that could be used to predict the error (Tg - Ts) in the temperature measurement.
(b) Assuming the flue gas to have the properties of atmospheric air, evaluate the error for Tl = 300oC, Ds = 0.6 m, Dt = 10 mm, mg = 1 kg/s, T8 = Tsur = 27°C, e1 = e3 = 0.8, and ho = 25 W/m2 · K.
air is considered as an ideal gas. dont use gas table for gas properties just assume that both cv and cp are constants.
A US Department of Energy article states that a leak of one drip of hot water per second can cost $1.00 per month. Making reasonable assumptions about drop size and unit cost of energy, determine if this claim is reasonable.
Determine the magnitude of the resultant force acting on a 5 kg particle at the instant t=2 s. if the particle is moving along a horizontal path defined by the equations r=(2t+10) m and theta = (1.5t^2-6t) rad, where t is in seconds
a for pt at 20 c calculate how many unit cells there are per cubic meter.bhow many total interstitial sites are there
Create a (Matlab) program (not Excel!) which allows you to vary the geometric parameters (rb {bottom radius of ask; rt {top radius of ask; h { initial liquid height; A { hole area; N { number of discretization points).
a refrigerator operates with a coefficient of performance of 4.2 and requires an electrical input of 700 w. determine
Please use the radiation fundamental and sun’s size to recalculate the sun radiation power and mass loss rate. Please also estimate the radiation reaching the earth!
a system executes a power cycle while receiving 800 kj by heat transfer at a tem-perature of 1600 k and discharging 120
Friction between the piston and cylinder wall can be neglected because the process occurs so slowly. For the air, determine the initial and final pressures in kPa and the boundary work for the process in kJ.
Helium is to be compressed from 120kPa and 315K to 700kPa and 450K. A heat loss of 20kJ/kg occurs during the compression process. Neglecting kinetic energy changes, determine the power input required for a mass flow rate of 78kg/min. Round to nearest..
Geoffrey is building an electronic circuit on a breadboard. He needs to supply his circuit with a 1500 ohm resistance. But he does not have any 1500 ohm resistors on hand. All he has is a box of 1000 ohm resistors.
a person is riding merrily along on his road bicycle at v mph. what is the approximate minimum speed v in mph necessary
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd