Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Develop a series 90-30 program that functions a motor forward/reverse controller.. Design your circuit so that the stop push button must be pressed before the motor can switch direction. Also incorporate a 5 second delay to inhibit restart after the stop push button has been pressed. Green light should be on when motor is running forward and the white light should be flashing when in .
If I have a resistor that is 10 Ohms and has a voltage drop of 4.2 V, how much current is flowing through the resistor?
A 15kV:175kV, 125 MVA, 60 Hz single-phase transformer has primary and secondary impedances of 0.0095+j0.063 per unit each. The magnetizing impedances is j148 per unit. All quantities are in per unit on the transformer base.
A sinusoidal message signal has a frequency of 10 Hz. The signal is the input to an FM modulator with an index of 8. Determine the bandwidth of the modulator output if a power ratio, Pr = 0.8 is required.
find the shortest length L of the line open-circuited at its load end so that the input impedance of the line at frequency f = 5GHz is the same as the impedance of a capacitor of capacitance C=10pf of the same frequency.
An op amp differential amplifier is built using four identical resistors, each havign a tolerance of ±5%. Calculate the worse possible CMRR.
find the current that flows in a silicon bar of 10 micrometerlength having a 5 X4 micrometer cross section and having freeelectron & hole densities of 10^5/cm^3 & 10^15/cm^3 ,respectively, when a 1V is applied end-to-end. Use Mn =1200cm^2/VS; Mp=5..
50 kmol per hour of air is compressed from p1 = 1.2 bar to P2 = 6.0 bar in a steady-flow compressor. Delivered mechanical power is 98.8KW. Temperature and velocities are: T1= 300K T2= 520K u1= 10m s^-1 u2= 3.5m s^-1
Construct the straight line Bode plot of the gain. Is this a low-pass, high-pass, bandpass, or bandstop function Estimate the cutoff frequency and the passband gain. Note that s = jw. This problem uses the letter T for system function.
Perform the calculation from t = 0 to 20 s with step size of 1 s. Use an initial condition that the parachutist has an upward velocity of 20 m/s at t = 0. At t = 10 s, assume that the chute is instantaneously deployed so that the drag coefficient ..
A sampled-data system such as that presented in problem (i) has a sampling period T = 0.05s and has G(z) = K (z3 + 10.3614z2 + 9.758z + 0.8353) / (z4 - 3.7123z3 + 5.1644z2 - 3.195z + 0.7408) 1. Determine K when the two real poles break away from the ..
A DC source of 48V is connected to one end of the cable. The other end of the cable supplies a DC load. If the load current is 12.5 A, calculate the voltage drop due to the cable resistance and the laod voltage.
the 4-bit fibbonaci counter is a counter which counts as 011235813011235....implement a multiple mode counter which can
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd