Deternine the duct length required to reach mach 06

Assignment Help Mechanical Engineering
Reference no: EM13608800

Air flow enters a constant-area insulated duct with a Mach number = 0.2. The duct diameter is 10 mm and the friction factor is 0.02 . (A) Deternine the duct length required to reach Mach 0.6 (B) Determine the length required to attain Mach 1.0 (C) Now suppose that an additional 750 mm of duct length is added. If the same initial stagnation conditions are maintained, determine the reduction in flow rate that will occur. (D) Now suppose that the duct (the duct whose length gave Ma = 1 at the outlet) is extended by 92.2%. If the same initial inlet stagnation conditions are maintained, determine the reduction in flow rate that will occur.

Reference no: EM13608800

Questions Cloud

A machine cost 800000 on april 1 2012 its estimated salvage : a machine cost 800000 on april 1 2012. its estimated salvage value is 80000 and its expected life is eight years.
How much revenue per account would be sufficient for : rotelco is one of the largest digital wireless service providers in the united states. in a recent year it had
Determine the horizontal distance between the launching : the track for a racing event was designed so that riders jump off the slope at 30 angle from a height of 5 ft. the
General population is skewed to the right the mean degree : general population is skewed to the right the mean degree of affection is 60 standard deviation is 16. sample 100
Deternine the duct length required to reach mach 06 : air flow enters a constant-area insulated duct with a mach number 0.2. the duct diameter is 10 mm and the friction
Rbc inc uses a job order costing system in which each : rbc inc. uses a job order costing system in which each client is a different job. rbc inc. traces direct labor daily
Suppose a manufacturing company makes a certain item the : suppose a manufacturing company makes a certain item. the time to produce each item is normally distributed around a
The temperature of the water is 20 degrees celsius what is : water flows at 0.25ls through a 9.0-m-long garden hose 2.5cm in diameter that is lying flat on the ground.part a the
New wave co sold 14000 annual subscriptions of game life : new wave co. sold 14000 annual subscriptions of game life for 51 during december 2012. these new subscribers will

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the angle of twist of the end b

determine the angle of twist of the end B of the solid section relative to end C. The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The solid section has a diameter of 40 mm.

  Determine the maximum lift force provided by the pump

the velocity of a lift increases uniformly from zero to its maximum value at mid-height (1.4m) in 7.5s and then decreases uniformly to zero in 7.5s. The peak power output is 6kW when the velocity is maximum, determine the maximum lift force provid..

  How many engagement point on flywheel would be necessary

How many engagement points on the flywheel would be necessary to make this machine safe

  What could be some of the strategies

How may data be managed to support a function (billing, human resources, accounting, finance, sales/marketing, training)?

  Find the volume rate of ?ow in ab

Find the volume rate of ?ow in AB, the velocity in BC, the velocity in CD and the diameter of CE.

  Determine the flow rate of stream and the thermal efficiency

an ideal rankine cycle produces 100 MW of power. If the steam enters the turbine at 100 bar and 500C and is condensed at 1 bar, determine the flow rate of stream and the thermal efficiency.

  The rigid gate oab shown in the figure below is hinged at o

the rigid gate oab shown in the figure below is hinged at o and rests against a rigid support at b. what minimum

  Determine the frequency response and m omega and phiv

determine the frequency response and m omega and phiv omega for an instrument having a time constant of 10 ms.

  A 250 g 230-cm-diameter plastic disk is spun on an axle

a 250 g 23.0-cm-diameter plastic disk is spun on an axle through its center by an electric motor. what torque must the

  Calculate net positive suction head (npsh) for the system

A pump station has been designed to lift water out of a 6 metre deep pit (vented to atmosphere) via a centrifigual pump mounted at ground level.   Calculate the Net Positive Suction Head (NPSH) for the system ?

  Draw the shear and bending-moment diagrams

draw the shear and bending-moment diagrams for the beam and loading shown and determine the maximum normal stress due to bending.

  In an em wave traveling north the e field oscillates

question in an em wave traveling north the e field oscillates vertically and has a frequency of 85.0 khz and an rms

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd