Determining the periodic currents

Assignment Help Mechanical Engineering
Reference no: EM13949347

Find the rms value of each of the following periodic currents:

a. i(t) = cos 450+ 2 cos 450A

b. i(t) = cos 5+ sin 5A

c. i(t= cos 450+ 2A

d. i(t) = cos 5+ cos(5π/3A

e. i(t) = cos 200+ cos 400A

Reference no: EM13949347

Questions Cloud

What is the appropriate average cash balance now : Humphrey’s Housing has been practicing cash management for some time by using the Baumol model for determining cash balances. Some time ago, the model called for an average balance (C*/2) of $500; at that time, the rate on marketable securities was 4..
Find the average power delivered to the resistor : A current source i(t) is connected to a 100-Q resistor. Find the average power delivered to the resistor, given that i(t) is:
Total assets of firm are unaffected by stock dividend : If the total assets of a firm are unaffected by a stock dividend, then:
What is the new price per flying hour : This will be accomplished by revising the price paid per flying hour based on the revised estimates of flying hours. What is the new price per flying hour?
Determining the periodic currents : Find the rms value of each of the following periodic currents:
How corporate valuation model and adjusted present value : Explain how the corporate valuation model and the adjusted present value (APV) method are used to estimate the value of a target company. If someone did a complete and careful analysis of a given target using both of these methods, would they produce..
What is the appearance of the relation result : In terms of the relations shown below, what is the appearance of the relation RESULT after executing each of these instructions?
Calculate operating cash flow if earnings before interest : If Earnings Before Interest and Taxes (EBIT) is $93,000, calculate Operating Cash Flow if Sales is $350,000, Cost of Goods Sold (COGS) is $140,000, Fixed costs is $43,000, Selling, General, Administrative Expenses (SGA) are $28,000, Depreciation is $..
What is the economic ordering quantity for chips : Aberwald Corporation expects to order 126,000 memory chips for inventory during the coming year, and it will use this inventory at a constant rate. Fixed ordering costs are $175 per order; the purchase price per chip is $25; and the firm's inventory ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the max shear developed on the web of this beam

a w16 x 50 steel beam supports a uniform load and a concentrated load. the distributed load is 1.5 kipft and

  Estimate the thickness of the boundary layer

It is assumed that a boundary layer begins to develop about 12 km from shore. If the wind speed averages 18 m=s, estimate the thickness of the boundary layer and the shear stress on the surface of the water near the shore.

  Two kilograms of carbon monoxide in piston-cylinder assembly

Two kilograms of carbon monoxide in a piston-cylinder assembly, initially at 1 bar and 27C, is heated at constant pressure with no internal irreversibilities to a final temperature of 227C.

  Construct the phase diagram for hypothetical metals

Construct the phase diagram for hypothetical metals A and B, between 20°C (room temperature) and 700°C, given the following information: the maximum solubility of B in A is 4wt% B, occurring at 420°C; an intermetallic compound, AB, exists at 30wt%B; ..

  The adiabatic flame temperature

Calculate the adiabatic flame temperature attained when methane at 298k, is combusted (a) with oxygen in the molar ratio air/CH4 = 9.524. Assume that CO2 and H2O are the products of the combustion. The adiabatic flame temperature is that temperature ..

  Determine the smallest allowable value of the coefficient

determine the smallest allowable value of the coefficient of static friction between the collar and the rod if the collar is not to slide when a) a =15° b)a = 45°. Indicate for each case the direction of the impending motion.

  It is desired to put oil hole through a part subjected to a

it is desired to put oil hole through a part subjected to a stress field given by sigma xx 15 ksi sigma yy -15 ksi

  Downward motion vo of the upper disk

An incompressible fluid is squeezed between two disks by downward motion Vo of the upper disk. Assuming 1-dimensional radial outflow, find the velocity V(r).

  Compute the maximum contact pressure and the width of

two mating spur gears are 20 mm wide and the tooth profiles have radii of curvature at the line oif contact of 10 and

  The pan is hot 80c and the room is cool 20c calculate the

a hot surface on a stovetop faces upwards. it is a pan whose diameter is 10 inches. the surface of the pan is dull with

  Find the final mass of nitrogen in the tank and the final

a steel cylinder initially contains nitrogen gas at 200kpa and 25 c. the cylinder is connected to a suply line

  Determine the rotation angle of the second degree of freedom

Determine the rotation angle of the second degree of freedom, theta2, that must be used to bring the effector to the specified configuration.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd