Given the Electrical Rating: 120V 60Hz and LED Bulb Rating:3.3 V of a lamp with 20 LED lights. What is the wattage of this lamp?

Explain the chemical formula and systematic name : Give the chemical formula and systematic name for aurous sulfide, which is named using the older nomenclature. |

Determine how are the wires connected to the switches : How are the wires connected to the switches where there are two switches that can operate a single light |

Explain water solution would be acidic : For each of the salts listed below indicate whether its water solution would be acidic , basic or neutral. NaBr, Na2Co3, KHSO4, KCN, NH4CH3COO, BaF2 |

What was your average velocity during breaking : When you see a traffic light turn red, you apply the breaks until you come to a stop. what was your average velocity during breaking |

Determine what is the wattage of the lamp : Given the Electrical Rating: 120V 60Hz and LED Bulb Rating:3.3 V of a lamp with 20 LED lights. What is the wattage of this lamp |

What is the phase difference between the sound waves : At a point P, the path lengths from two point sound wave sources have a difference of 1/4 l. What is the phase difference between the sound waves at poiunt P |

Determine the combine bit rate of the two channels : The left and right channels of a analog stereo signal are sampled at a 45kHz with each signal being converted into a digital bit stream using a 12-bit A/D converter. Determine the combine bit rate of the two channels after sampling. |

Describe potential problems can occur with electric tools : Describe potential problems that can occur with portable electric tools that might expose a worker to electric shock. |

Explain method for find out the quantity of dissolved oxygen : A method for determining the quantity of dissolved oxygen in natural waters requires a series of redox reactions. Balance the following chemical equations in that series under the conditions indicated |

## Determine the stability of the system and design the circuitA system or component is imaginary (critically ) stable if at least one real part of the roots of the characteristic equation is equal to zero. Determine the stability of the following system and design the circuit. |

## Calculate the assembly energy for the configurationFour equal point charges Q form a square of side length a. Calculate the assembly energy for this configuration. |

## What is the resistivity of the wire and conductivityWhat is the resistivity of the wire? conductivity? Using the original dimensions of the wire, how much current can you pass through the wire until a 5V signal is degraded 5% or more? |

## Calculate the unit step response of the dt systemCalculate the unit step response of the DT systems with the following impulse responses: a-) h[k]= u[k+6]- u[k-10] b-) h[k]= 3^k- u[-k] |

## Design a 3-input cmos or-gate using mosfetsDesign a 3-input CMOS OR-gate using MOSFETs on the CD4007 chip. Make certain that the power dissipation is zero when the output is both logic 1 and logic 0. As an added challenge, design the OR gate using the minimum number of CD4007 chips. |

## Design metallurgical channel thickness of n-channel jfetDesign (determine) the metallurgical channel thickness of an n-channel silicon JFET such that the pinch off voltage is -3.0V. The doping parameters are NA=3x1018cm-3 and Nd=2x101616 cm-3. |

## What is the impulse response for the systemConsider the following differential equation, where x(t) is the input and y(t) is the output: d/dt y(t)+5y(t)=2x(t) Suppose the input is x(t) = 4u(t) and the initial condition is y(0-) = 6 1. What is the impulse response for the system |

## Compute and plot the response of the system to input signalA system is described by the impulse response h(t) given in the following problems. Compute and plot the response of the system to the input signal x(t). (a) h(t) = t; 0 |

## Find the average velocity of the electrons in the wireA copper wire has a diameter of 2.05 mm and carries a current of 5 A due solely to electrons. (these values are common in residential wiring.) Each electron is has a charge of of -1.6 × 10-19 C. |

## Find the change in resistance per pound placedWe will weigh objects by a strain gauge or R = 120 Ohms, GF= 2.02 mounted on copper column of 6-in. diameter. Find the change in resistance per pound placed on the column. Is this change an increase or decrease in resistance |

## Find the probability that the headquarters is destroyedSuppose that independent missiles A, B, C have probabilities .4, .5, and .6 of hitting the enemy's headquarters, respectively. Assume that the enemy's headquarters will be destroyed with a probability .3, |

## Compute the total signal power from the specturmA communication system must transmit the following real valued signal: v(t) = 4cos(2pi*10MHz*t) + 2cos(2pi*20MHz*t)+cos(2pi*30MHz*t)V For this signal, sketch the positive-frequency power specturm P(f>0) |

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd