Determine what is the switching voltage

Assignment Help Electrical Engineering
Reference no: EM13227830

Suppose that two optical guides embedded in a substrate such as LiNbO3 are coupled as in the below figure and the transmission length Lo=10mm. If the coupling separation d is =10µm, n = 2.2, the operating wavelength is 1.3µm taking a rough coefficient r = 10 x 10-12 m/V, what is the switching voltage?

Reference no: EM13227830

Questions Cloud

State a gaseous hydrogen and carbon containing compound : A gaseous hydrogen and carbon containing compound is decomposed and found to contain 85.63% C and % H by mass. The mass of 258 mL of the gas, measured at STP, was found to be 0.646 g. What is the molecular formula for this compound
Use an appropriate technique to develop a forecast : Use an appropriate technique to develop a forecast for the expected number three weeks Can someone please show me how to work this problem?
Explain precipitate immediately on addition of hcl : Typical lab experiment exploring le chateliers principle. HCl is added to Pb(NO3) until precipitate forms. Question asks: Explain why PbCl2 did not precipitate immediately on addition of HCl. What condition must be me by [PB2+] and [cl-] if PbCl2 i..
Which role is more important : When communicating a change, which role is more important: reporter of information or sense maker? Why
Determine what is the switching voltage : Suppose that two optical guides embedded in a substrate such as LiNbO3 are coupled as in the below figure and the transmission length Lo=10mm. If the coupling separation d is =10µm, n = 2.2, the operating wavelength is 1.3µm
What is the mode integer m of the peak radiation : Consider an AlGaAs based heterostructure laser diode which has an optical cavity of length 200 microns. The peak radiation is at 870 nm and the refractive index of GaAs is about 3.7.  What is the mode integer m of the peak radiation
Explain structure of the major organic product : Draw the skeletal structure of the major organic product formed when benzaldehyde reacts with Cl2 in the presence of AlCl3. Assign atomic charges where appropriate.
Describe system using feedback loops and detailed narrative : Be sure to describe which of the Control Theory's would apply to the concept. Be sure to describe the system using feedback loops and a detailed narrative.
How much optic power must reach the receiver : An analog system has a bandwidth of 10 MHz, a photodetector of = 0.5 A/W and ID = 1 nA, and a signal to noise ratio (SNR) of 30 dB. The receiver's temperature is 270 C and the load resistance is 50 .

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Determine power and limiting error of the power

determine power and limiting error of the power?

  Calculate the sacrifice ratio

Inflation in years 1-5 equals 3.1 percent, 2.2 percent, 1.6 percent, 1.3 percent, and 1.1 percent, respectively.

  What would be the new pressure of the gas in psig

When the piston is at its bottom dead center, the gas is initially at 10 psig, 65°F, and 10.5 in 3 . After compression and when the piston is at top dead center, the gas is 180°F and occupies 1.5 in 3 . What would be the new pressure of the gas in..

  Calculate the unit length capacitance of the cable

The cylindrical coaxial cable with the cross section shown below, has inner and outer radii of 5mm and 15mm respectively. The dielectric parameters are; er=2, signma=5*10^(-10) S/m and Ur=1.

  Explain radio systems

Radio Systems, In design of radio systems that incorporate wireless networks, considerations must be taken such as user access, transmission direction, switching and signal strength.

  Explain circuit to be used in a process control system

Design an alarm circuit to be used in a process control system. Temperature (T), pressure (P), flow (F), and level (L) of a fluid are each monitored by separate sensor circuits that produce a high logic output signal when the following indicated p..

  How far does the sled go before stopping

A sled is traveling at 4 m/s along a horizontal stretch of snow. The coefficient of kinetic friction is 0.05 . How far does the sled go before stopping ?

  What is the resolution of the representation

suppose we use a 32-bit unsigned fixed-point representation with the binary point to the left of the most-significant bit of the 32-bit number. (We'll have a range of 0 - almost 1.) What is the resolution of this representation

  Compute the power absorbed by an element in a circuit

Compute the power absorbed by an element in a circuit, but for a simple sinusoidal current i = sin(2πt/T) where T = 1 s.

  Draw the rom truth table for the seven segment

Draw the ROM truth table for the seven segment

  Consider a three-phase distribution feeder

Consider a three-phase distribution feeder with line reactance of10 ohm supplying a three-phase Y-connected load of 200 kVA at power factor of 0.85 lagging.

  What would be the baud rate if the intial value of the timer

Write a sequence of instructions to initialize and run the timer to geneate an 800 baud rate clock. what would be the baud rate if the intial value of the timer was set to 9AH

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd