Determine what is the required voltage at the sending end

Assignment Help Electrical Engineering
Reference no: EM13291065

Three parts of asingle-phase electric system are designated A,B and C and areconnected to each other through transformers. Neglect transformerresistance and magnetizing current. The transformers are rated as follows:
A-B Transformers: 9.6kVA, 500V/1.5kV, leakage reactance 5%(Xeq=0.05 p.u.)
B-C Transformers: 7.2kVA, 1.2kV/120V, leakage reactance4% (Xeq=0.04 p.u.)
The line (in circuit B) has an impedance of 0.5+j3.0 Ω.The load (in circuit C) operates at 120V, 6kVA at 0.8 power factorlagging.
(a) Determine the value of the load impedance in ohms
(b) Determine the actual ohmic impedances of the twotransformers referred to both their primary and secondarysides.
(c) Chooso=ing 1.2kV as the voltage base for circuit B and10kVA as the systemwide kVA base, express all system impedance inper unit.
(d) What is the required voltage at the sending end (circuitA) according to the given loading conditions?

Reference no: EM13291065

Questions Cloud

What is the project coefficient of variation : Cheng Inc. is considering a capital budgeting project that has an expected return of 25% and a standard deviation of 30%. What is the project's coefficient of variation?
Compute the number of cys residues in the peptide : Calculate the number of Cys residues in the peptide assuming that the total solution volume has not changed after addition of Ellman's reagent and that the stoichiometry of the reaction is 1:1 (i.e. 1 mole of the yellow dye is produced from 1 mole..
What will the price be 5 years from now : A 25-year, $1,000 par value bond has an 8.5% annual payment coupon. The bond currently sells for $925. If the yield to maturity remains at its current rate, what will the price be 5 years from now?
What was the bullets flight time : A rifle is aimed horizontally at a target 60 away. The bullet hits the target 2.5 below the aim point. What was the bullet's flight time
Determine what is the required voltage at the sending end : Three parts of asingle-phase electric system are designated A,B and C and areconnected to each other through transformers. Neglect transformerresistance and magnetizing current. The transformers are rated as follows
What is the extent of the obesity problem in the united stat : What individual, social, and environmental factors have led to the epidemic of obesity in the US? Specify at least one of each. Consider community design and the evidence presented by Frank et al (2004) in your response.
What is the maximum price you should be willing to pay : If you require an 8.4% nominal yield to maturity on this investment, what is the maximum price you should be willing to pay for the bond?
Find the magnitude of the torque exerted by magnetic field : A current of 12.0 mA is maintained in a single circular loop with a circumference of 3.70 m. find the magnitude of the torque exerted by the magnetic field on the loop
Explain tlc plate for your recrystallized benzoic acid : How many spots should you see on a TLC plate for your recrystallized benzoic acid (assuming your recrystallization worked)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the noise power and noise voltage applied to receiver

A 300 ohms resistor is connected across the 300 ohms antenna input of a television receiver. The bandwidth of the receiver is 6 MHz, and the resistor is at room temperature (20' C). Find the noise power and noise voltage applied to the receiver in..

  Design preamplifier that has the characteristics mentioned

Design an EKG amplifier interface to a 6811/6812. The biopotential is a ±5-mV signal measured between the left and right arms using silver-silver chloride electrodes. A third electrode is placed in the right leg and is used as a reference.

  Explain how to find the signal relatively to real time

Find and sketch y(t) when x(t) is a train of action potentials (model the action potentials as δ-impulses) 100 msec apart from each other. Justify your drawing on the basis of your answer in (c) above and related properties of LTI systems and δ(t)..

  Find the smallest possible diameter

A micrometer caliper is used to measure the diameter of a bolt and a reading of 0.768 inches is obtained. Based on this measurement, find the smallest possible diameter and the largest possible diameter.

  Explain how much power does the third element absorb

a circuit consists of three elements in series. a source delivers 90 watts and one of the passive elements absorbs 20 watts. how much power does the third element absorb.

  Determine the average no load steady state speed

The rotor of a 3phase, 5kw, 400v, 50Hz, slip ring indution motor is wound for 6 poles while its stator is wound for 4 poles. The approx average no load steady state speed when this motor is connected to 400v, 50Hz what is the supply

  What is the current through the resistor

A 1.0 dc voltage source is connected across a 10 ohm resistor. What is the current through the resistor if (a) the voltage source is ideal (b) the voltage source has internal resistance 0.1 ohm (c) internal resistance 1.0 ohm

  Write the expression for the current

Write the expression for the current through the capacitor after the switch is closed. The circuit is a 60 Volt circuit

  Determine the magnitude and direction of the velocity

Two marbles are rolled towards each other. One marble (m1 = 4.2 g) has a speed of 5.1 m/s towards the right. The other marble (m2 = 6.1 g) has a speed of 3.8 m/s to the left. After the collision, the first marble moves to the left at a speed of 3...

  Find the truth table for a three-input majority circuit

A majority circuit is a circuit with an odd number of inputs whose output is a 1 if and only if a majority of its inputs are 1. (a) Find the truth table for a three-input majority circuit. (b) From the truth table,find the Boolean equation for the ci..

  Determine the forth sum bit of a binary adder

Write an algebraic expression for S3, the forth sum bit of a binary adder, as a function of inputs x0, x1, x2, x3, y0, y1, y2, and y,3. Assume that c0=0, and do not attempt to "multiply out" or minimize the expression.

  Design an embedded system to turn on an led

Design an embedded system to turn on an LED when it is dark and turn off of LED during the day time.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd