Determine what is the maximum zener current allowed

Assignment Help Electrical Engineering
Reference no: EM13252081

What is the primary use for a Zener diode?

Name 4 opto-electronic devices.

For an ideal Zener, is the Zener voltage is 15v and the power rating is 750mW, what is the maximum zener current allowed?

What is the relationship between base current and collector current called?

Reference no: EM13252081

Questions Cloud

What information can be gathered from a line spectrum plot : Discuss what is meant by line spectra and what information can be gathered from a line spectrum plot. Discuss the similarities and differences between the Fourier Transform and the Laplace Transform.
Find the current through each resistor : A circuit consists of a battery connected to three resistors (65?, 26?, and 170?) in parallel. find the current through each resistor
What are the decisions that need to be made : Calculate by hand how many labor-hours would be available in January and February. Calculate by hand the total costs in January and February.
Design a wireless sensor node : Develop a Sensor Circuit using commodity component and design a wireless sensor node using commodity wireless modules
Determine what is the maximum zener current allowed : For an ideal Zener, is the Zener voltage is 15v and the power rating is 750mW, what is the maximum zener current allowed What is the relationship between base current and collector current called
What is the maximum tension in the rope : A 56 kg student runs at 5.0 m/s, grabs a hanging rope, and swings out over a lake, What is the maximum tension in the rope?
Are the process average and range in statistical control : a. Are the process average and range in statistical control?
How many units are needed to break even : A manufacturing process has a fixed cost of $310,000 per month. Each unit of product being producted contains $32 worth of material and takes $36 of labor. How many units are needed to break even if each completed unit has a value of $118?
How fast is the center of mass of the two-stone system : A stone is dropped at t = 0. A second stone, with 6 times the mass of the first, is dropped from the same point at t = 56 ms. How fast is the center of mass of the two-stone system

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine voltage range that would be converted to pcm code

For a 12-bit linear PCM code with a resolution of 0.02 V, determine the voltage range that would be converted to the following PCM codes.  (a) 1 0 0 0 0 0 0 0 0 0 0 1 (b) 0 0 0 0 0 0 0 0 0 0 0 0 (c) 1 1 0 ..

  Find the overall gain gv and the equivalent circuit

Two amplifiers(CS) connected in cascade. The input voltage to the first stage has a source voltage Vsig and Rsig= 100KOhm. Rv=10KOhm AND IS CONNECTED TO THE DRAIN OF THE SECOND STAGE. BOTH TRANSISTORS HAVE Id=.25mA and Vov=.25V

  Determine the weigh of the rod in units of pounds-force

A rod on the surface of Jupiter's moon Callisto has a volume of 0.3 cubic meters. Determine the weigh of the rod in units of pounds-force. The specific gravity is 4.7 gravitational acceleration on Callisto is 1.25 meters per second squared.

  Which filters are recursive and which are nonrecursive

Compute the first 10 samples of the step response for the nonrecursive difference equation: y(n) = x(n) -0.5x[n-1]-0.7x[n-2] Indentify which of the following filters are recursive and which are nonrecursive.

  Determine the minimum order of the filter at sampling rate

the -3 dB frequency for low pass Butterworth filter is 2.5 kHz. The stop band begins at 3.8 kHz, with an attention of 35 dB. Determine the minimum order of the filter if the sampling rate is 8 kHz

  How long a 1 inch square bar of copper have resistance

Using coppers resistivity of 10.30 CM-olm/ft at +25 °C, find how long a 1 inch square bar of copper would need be to have a resistance of 1 at +20 °C

  For what values of f in range sinusoid produce same sample

The continuous-time sinusoid x(t) = cos(300?t) is sampled every Ts = 2.0 ms, so that x[n] = x(0.002n) For what other values of f in the range 0 Hz to 2.0 KHz does the sinusoid v(t)

  Design a sequential circuit with three d-type flip-flops

A sequential circuit with three D-type flip-flops Y1Y2Y3, input X and output Z is defined with the following input/output functions: D 1 = X Y 3 + X Y 1 Y 3 D 2 = X  ( Y  3 + Y 2 ) + X Y 2 Y 3 D 3 = X Y 3 + Y 2 Y 3 Z = Y3

  What is mac os xs present day file system

8. What is Mac OS X's present day file system A) Macintosh Filing System (MFS) B) Hierarchical Filing System (HFS) C) Hierarchical Filing System Extended (HFS+) D) Extended File System (EXT) Th..

  Draw the sympol and truth table of the gate

draw the sympol and truth table of the gate that corresponds to the action of the logic gate.

  Determine if there is a difference in compression strength

An engineering statistician wants to conduct a test to determine if there is a difference in the compression strength of two different manufactures of reinforced concrete columns.

  Find a volume charge density px nd the flux through surface

1. Point charges Q1 and Q2 are respectively, located at(4,0,-3) AND (2,0,1). If Q2=4nC, find Q1 such that a. E at (5,0,6) has no no z component b. The force on a test charge at (5,0,6) has no x component

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd