### Determine what is equilvalent circuit for the combination

Assignment Help Electrical Engineering
##### Reference no: EM13294980

Two ideal diodes are placed in series, pointing in opposite directions. What is the equilvalent circuit for the combination? What is the equilvalent circuit if the diodesare in parallel and pointing in opposite directions?

#### Questions Cloud

 Find the ratio of the masses of the particles : Two particles are moving along the x axis. Particle 1 has a mass m1 and a velocity v1 = +3.7 m/s. Find the ratio m1/m2 of the masses of the particles What annual interest rate is required to accumulate : What is the present value of this annuity if the payments are invested in n account that pays 10 percent interest annually? 10 percent compounded annually? Describe what is the final temperature of the mixture : If you have 340.0 mL of water at 25.00 °C and add 120.0 mL of water at 95.00 °C, what is the final temperature of the mixture. Use 1.00 g/mL as the density of water. Find the ratio of the masses of the particles : Two particles are moving along the x axis. Particle 1 has a mass m1 and a velocity v1 = +3.7 m/s. Find the ratio m1/m2 of the masses of the particles Determine what is equilvalent circuit for the combination : Two ideal diodes are placed in series, pointing in opposite directions. What is the equilvalent circuit for the combination What is the equilvalent circuit if the diodesare in parallel and pointing in opposite directions Determine if the inverse applies for this value : All solutions to the differential equation y'-2y=0 should also be solutions to the differential equation y''-ay'+ay=0. Determine the constant a such that this is true. Determine the mutual inductance of these solenoids : One solenoid is centered inside another. The outer one has a length of 54.0 cm and contains 6800 coils, What is the mutual inductance of these solenoids What is the future value of this cash flow stream : Does the office renovation and subsequent lease agreement appear to be a good investment investment for the company? (Hint: Compare the cost of renovation with the present value of the lease payments. Use a 10 percent discount rate for the analysi.. How to evaluate the molar mass of the unknown : Stearic acid has a freezing point of 71.20 C and a Kf of 4.890C/m. A 400.0 g quantity of stearic acid to which 50.0 g of an unknown is added has a freezing point of 68.00C. Calculate the molar mass of the unknown.

### Write a Review

#### Explain the differences among a truth table and state table

Explain the differences among a truth table, a state table, a characteristic table, and an excitation table. Also explain the difference among a boolean equation, a state equation, a characteristic equation and a flip-flop input equation.

#### What is the maximum strength of the waves electric field

The maximum strength of the magnetic field in an electromagnetic wave is 3.44E-6 T. What is the maximum strength of the wave's electric field

#### What is the angle at each tip of the cottage

The cross section of a cottage 20 ft wide is an isosceles triangle. If the slope of a side is 1.75 and there is a second floor 9 feet above the ground floor,What is the angle at each tip of the cottage?

#### Measure current for different values of load resistance

The collector current was measured for different values of load resistance. It was noticed that the collector current was pretty much constant for the first 1900 ohms and then it fell drastically.

#### What value of k makes the system marginally stable

The characteristic equation ofthe system is q(s) = s^5+13s^4+33S^3+32s^2+20s+k^2 where k>0. a). Find the range of values of k for which the system is stable using the Routh-Hurwitz table. b) What value of k makes the system marginally stable

#### For how long would device tie up bus when transferring block

Consider a system in which a data transfer over a bus takes 500 ns. Transfer of bus control in either direction, from processor to I/O device or vice versa, takes 250 ns. One of the I/O devices has a data transfer rate of 50 KB/s and employs DMA.

#### Implement the equation if a power amplifier is available

A 4 to 20mA control signal is loaded by a 100Ohm resistor and must produce a 20 to 40V motor drive signal. Develop the equation relating the input current to the output voltage.

#### Find characteristic polynomial and characteristic equation

An LTIC system is specified by the equation ( D2 +5D + 6) y (t) = ( D + 1) x (t) . (a) Find the characteristic polynomial, characteristic equation, characteristic roots, and characteristic modes for this system.

#### Find when the triggering angle is greater than 140 degrees

The average voltage across the load when the triggering angle is 140 degrees. Keep in mind that the conduction is incomplete when the triggering angle is greater than 140 degrees.

#### What is time required for capacitor voltage for state value

A capacitor in an RC circuit with R = 5.00 W and C = 6.00 mF is being charged. What is the time required for the capacitor voltage to reach 86.5 percent of its steady-state value

#### Calculate the thickness of the velocity boundary layer

Consider cold windy breeze parallel to your face, with an average facial dimension along the flow of 5 cm. The air velocity is 1 m/s (corresponding to 2.2 miles per hour). Assume laminar flow.  1) Calculate the thickness of the velocity boundary la..

#### How many atoms are there in the unit cell

(a) How many atoms are there in the unit cell characterizing the Si lattice (b) Verify that there are 4.994 X 1022 atoms/cm' in the Si lattice at room temperature. (c) Determine the eenter-to-center distance between nearest neighbors in the Si lattic..