Determine ull load torque tfl in newton metres

Assignment Help Electrical Engineering
Reference no: EM13290925

A 75 kW, 8 pole star connected induction motor operates froma 415 V, 50 Hz supply and draws 140 A when supplying full load.Determine:
1. the synchronous speed Ns;
2. the rotor speed Nr if the full load slip is 2.5%;
3. full load torque TFL in Newton metres developed by the motor.

Reference no: EM13290925

Questions Cloud

Explain what will the current be when the speed is reduced : A separately excited DC generator,when running at 1200 RPM, supplies 200A at 125V to a circuit ofconstant resistance. What will the current be when the speed is reduced to 1000 RPM if the field current remains unchanged
Compute the volume in liters of calcium sulfate : Calculate the volume in liters of a 0.00360 mol/L calcium sulfate that contains 75.0g of calcium sulfate (CaSO4)
What are the two reasons for doing so : You own a bond portfolio and expect the market interest rate to increase for the foreseeable future. (a) What should you do with regards to the Duration of the portfolio and your own investment horizon? (b) What are the two reasons for doing so?
Find the magnitude and direction of given vector : Let B = 5.10 m at 60°. Let vector C have the same magnitude as vector A and a direction angle greater than that of vector A by 25°. Find the magnitude and direction of vector A
Determine ull load torque tfl in newton metres : A 75 kW, 8 pole star connected induction motor operates froma 415 V, 50 Hz supply and draws 140 A when supplying full load.Determine: 1. the synchronous speed Ns;
Calculate the current in the motor : A 120-V motor has mechanical power output of2.10hp. It is84.0%efficient in converting power that it takes in by electrical transmission into mechanical power. Find the current in the motor
What happen if a independant current source is in parallel : based upon the Norton thevenin equivalentcircuits (Method of short circuit through nodal analysis) When there is a short circuit present, any resistor in parallel will not have current running through it. But what if: 1) A independant current source ..
Calculate the present value of growth opportunities : Calculate the Present Value of Growth Opportunities based on the following information: Earnings Per Share = $8.00, Required Rate of Return = 14%, Dividends Per Share = $1.50, Return on Equity = 16%.
Explain didn''t have a computer or data system available : If you didn't have a computer or data system available, how would you measure the area of the peak. After all, someone's DUI may hinge on this measurement, and you may have to defend your calculation in court

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find out the minimum signal to noise ratio

Determine the minimum signal to noise ratio (s/n) in dB required in each communication channel to achieve a data rate of 270 kbps?

  Find the rms input noise power level

When the amplifier is operating with a bandwidth first of 10MHz, find? 1) The RMS input noise power level? 2) The audio output power level? 3) The RMS output noise power level?

  An ac sine wave is applied to the input of a full wave

An AC sine wave is applied to the input of a full wave rectifier. The output of the full wave rectifier is then applied to a half wave rectifier.

  Give the numerical value of the poles and zeros

a) Express the s-domain impedance of this series combination as a rational function, b) Give the numerical value of the poles and zeros of the impedance and verify your calculation by matlab.

  What frequency is present in the y projections

Assume that we have an image represents a sinusoidal variation orthogonal to the x-axis with amplitude of 10 and period of 1 cm, that repeats infinitely in all directions within the plane. Further assume an average intensity of 10.

  Investigate the effect of varying this ratio on the transfer

Investigate the effect of varying this ratio on thetransfer characteristics of the CMOS inverter in Fonstad, by sketching the characteristics forKN=50uA/V2 with KP = 50, 100, 250and 500uA/V2. In your sketch do accurate plots inregions I,

  Determine what is the linecurrent il and line voltage vl

a balanced 3 phase generater delivers 9.6 kw to a wye connectedload with an impedance 30 - j40 per phase. what is the linecurrent IL and line voltage VL

  How much work must be done to compress the section

An infinite grounded conducting tube of radius 10cm is centered on the z axis. A concentric charged tube of radius 6 cm has a surface charge density of 24 uC/m2. A 1m long section of the charged tube is compressed to change its radius to 3 cm.

  Calculate total active-reactive and complex powers supplied

A 4157-V rms, 3-phase supply is applied to a balanced Y-connected three-phase load consisting of three identical impedances of 48 at angle 36.87 degrees . Taking the phase voltage Van as reference

  Determine the mid point of the voltage divider

An n-channel JFET needs a NEGATIVE voltage applied to its GATE, relative to its SOURCE. If you have a single POSITIVE supply applied to the MASTER loop of a JFET, the mid point of the voltage divider will also be a positive voltage

  Design a single-stage 3-input compound cmos minority gate

A majority gate returns a true output if more than half of the inputs are true. So, a 3-input majority gate outputs a ‘1' if at least two of its inputs are ‘1'. A minority gate generates the complement, that is it outputs ‘0' if at least two of th..

  Calculate the armature current-total losses in the machine

A 240kW 500 Volt 1750rpm separately excited dc generator has an overall efficiency of 94%. The shunt field resistance is 60ohms, and the rated current is 5amps. The I^2R loss in the armature is 0.023pu.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd