Determine the volume of the tank in m3 and the final

Assignment Help Mechanical Engineering
Reference no: EM13620280

Five kilograms of water are contained in a closed rigid tank at an initial pressure of 20 bar and a quality of 50%. Heat transfer occurs until the tank contains only saturated vapor. Determine the volume of the tank, in m^3, and the final pressure, in bar. Also, show the process on both a P-v and T-v diagram.

Reference no: EM13620280

Questions Cloud

Calculate the expected number of bad checks the grocery : in the table below x number of bad checks and px is the p that x bad checks will be passed in a
Determine a the thermal efficiency of the cycle b the mass : steam is the working fluid in an ideal reheat rankine cycle. steam enters the first-stage turbine at 8.0 mpa 480
Suppose the following data shows whether or not 10 randomly : suppose the following data shows whether or not 10 randomly selected voters approve 1 approve 0 dont approve the
Calculate the specific volume for carbon dioxide gas at 450 : calculate the specific volume for carbon dioxide gas at 450 k and 4000 kpa using a ideal gas equation b compressibility
Determine the volume of the tank in m3 and the final : five kilograms of water are contained in a closed rigid tank at an initial pressure of 20 bar and a quality of 50. heat
Combustion heats it to 1500 k in a constant-volume process : air in a piston-cylinder device has 400 degrees f 1000 kpa with a volume of 3.5 ft3. combustion heats it to 1500 k in a
The cooling continues to -10 degrees celcius state 3 show : r-134a in piston-cylinder arrangement is at 700 kpa and 80 degrees celcius. it is now cooled at a conswtant pressure to
What is the mean tax penalty for improperly filled : small business owners often look to payroll service companies to handle their employee payroll. reasons are that small
If we are testing the difference between the means of two : if we are testing the difference between the means of two normally distributed populations with samples of n1 10 n2

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Just before it lifts off a 10500 kg airplane is traveling

just before it lifts off a 10500 kg airplane is traveling at 60 fts. the total horizontal force exerted by the planes

  Estimate the ship speed

The kite cable makes an angle of 25 degrees with the horizontal. The velocity of the wind is 30 miles/hour. Neglect ship wave drag.

  Determine the value of force when the rod begins to yield

A 20-mm diameter rod made of a ductile material with a yield strength of 350 MPa is subjected to torque of 100 N.m and a bending moment of 150 N.m. An axial force is then gradually applied. Determine the value of force when the rod begins to yield..

  Carbon dioxide enters an adiabatic compressor at 100kpa and

carbon dioxide enters an adiabatic compressor at 100kpa and 300k at a rate of 0.5kgs and exits at 600kpa and 450k.

  Calculate a the mass of the bubble b the final temperature

a 2 mm diameter spherical air bubble is suspended in an insulating fluid . with a focused laser the bubble is heated so

  After a period of time the pressure in the tank rises to 15

1 initially an insulated rigid tank contains 3.86 kg of water at 265oc and 1 mpa. a heater in the wall of the tank

  The material hoist and the load have a total mass of 900 kg

the material hoist and the load have a total mass of 900 kg and the counterweight c has a mass of 150 kg. at a given

  The air leaves the diffuser with a velocity that is very

air at 10 deg c and 80 kpa enters the diffuser of a jet engine steadily with a velocity of 200 ms. the inlet area of

  Describe how you implement it using an open-loop system

Describe how you would implement it using an open-loop system

  It is within safety requirements

A rigid tank has a volume of 23.3 m^3 and due to safety requirements its pressure should not exceed 105 bar. If the tank has been filled with 1000kg of water vapor and is heated to 360°C check to see if it is within safety requirements.

  Determine the distance it travels before it stops express

a particle is moving along a straight line such that when it is at the origin it has a velocity of 8 ms part a if it

  Calibrated vibrometer output indicates a velocity amplitude

the waveform from a mechanical vibration is sensed by a velocity-sensitive vibrometer. the oscilloscope trave indicates

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd