Determine the volume of gas in the tank also plot pressure

Assignment Help Mechanical Engineering
Reference no: EM13636767

1000 kg of natural gas at 100 bar and 255 K is stored in a tank. If the pressure p, specific volume v and temperature T of the gas are related by the following expression (the teacher gave us the answer to be 8.84 m^3):

[5.18x 10 ^-3 T(v-.002668)] -8.91 x 10^-3/v^2

where v is in m^3/Kg, T is in Kelvin and p is bar, determine the volume of gas in the tank. Also plot pressure versus v and T for the isotherms T = 250, 500 and 1000 K. Note that the numbers in the above expression have their own units.

Reference no: EM13636767

Questions Cloud

How many grams of hydrogen gas were released by the : 1 the reaction of aluminum and potassium hydroxide isgiven below als koh 3h2o -----gtkaq aloh4 - 32 h2g a how many
What must the charge sign and magnitude of a particle of : q1. what must the charge sign and magnitude of a particle of mass 1.47 g be for it to remain stationary when placed in
Calculate the rates of exergy destruction in the compressor : air enters the compressor of a cold air-standard brayton cycle at 100 kpa 300 k with a mass flow rate of 6 kgs. the
Consider the formula used for any confidence interval and : consider the formula used for any confidence interval and the elements included in that formula. what happens to the
Determine the volume of gas in the tank also plot pressure : 1000 kg of natural gas at 100 bar and 255 k is stored in a tank. if the pressure p specific volume v and temperature t
A rock is tossed straight up with a speed of 24 ms when it : a rock is tossed straight up with a speed of 24 ms. when it returns it falls into a hole 9 m deep.what is the velocity
Use the normal distribution of sat critical reading scores : use the normal distribution of sat critical reading scores for which the mean is 500 and the standard deviation is 108
The surface temperature of the wall exposed to air is : the heat flux that is applied to one face of a plane wall is q 20 w m2. the opposite face is exposed to air at
A cart is propelled over an xy plane with acceleration : a cart is propelled over an xy plane with acceleration components ax 4.0 ms2 and ay -2.0 ms2. its initial velocity

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider the flow of air over a vertical flat plate at a

consider the flow of air over a vertical flat plate at a low velocity u1 in ambient pressure p1. the plate surface

  It is estimated that the refrigerator removes 3300 kjhr

1. a commercial refrigerator keeps food fresh at -12 ordmc. it is estimated that the refrigerator removes 3300 kjhr

  The drag characteristics of an airplane are to be

the drag characteristics of an airplane are to be determined by model tests in a wind tunnel operated at an absolute

  The power p required to drive a fan is believed to depend

the power p required to drive a fan is believed to depend on density p flow rate q impeller dia. d and angular veloctiy

  Determine the slenderness ratio

determine the slenderness ratio of a 5 m column with built end if its cross section is a circular with a radius of 40 mm and b 50 mm square use the concept of effective length.

  Calculate the specific volume of carbon dioxide 10 degrees

1. calculate the specific volume of carbon dioxide 10 degrees celsius and 80 quality?2. calculate the specific volume

  Design a v-beltchaon drive which limits the top speed to

a mini motor bike for chidren is powered by a 4 hp single cylinder gasoline engine governed to run at a maximum of 2250

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  The inefficiencies of engine components determine the force

consider an aircraft powered by a turbojet engine that has a pressure ratio of 9. the aircraft is stationary on the

  Explain what scm can do and in what it is important that

for the development of software products the scm software configuration management process is closely followed as a way

  Determine the bore diameter on the seat what will the

in a direct acting pressure relief valve 64 bar pressure is acting on the conical dart seating area and the dart is

  At time t 2 which particle has the higher velocity which

two particles are moving along a straight line starting beginning from x0 0 with a velocity of v0 10 at time t 0.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd