Determine the volume of chamber

Assignment Help Mechanical Engineering
Reference no: EM13212620

the piston diameters are d1=10cm and d2= 4cm .chamber 1 contains ikg helium , chamber 2 is filled with condensing watervapour and chamber 3 is evacuated. the entire assembly is placed in an environment whose temperature is 200c. determine the volume of chamber 1 when thermodynamic equillibrium has been estabilished.

Reference no: EM13212620

Questions Cloud

Determine the mass flow rate : (a) Draw and label a schematic of the system. (b) Determine the mass flow rate (kg/s) of water vapor neededand (c) the rate of exergy destruction (kW)
Draw and label a schematic of the system : A 10 kW electric heater is used to heat 2 kg of air contained in an insulated rigid tank from 400 kPa  and 50 °C to 200 °C. The ambient air temperature and pressure is 20 °C and 100 kPa, respectively.
Explain sulfur is used to crosslink isoprene : Sulfur is used to crosslink isoprene (C5H8) units in naturally occurring rubber to make vulcanized rubber, which is a harder material. If it takes 4 sulfur atoms to form a crosslink with 1 isoprene unit
Derive an expression for the net work transfer : (a) derive an expression for the net work transfer for the cycle. Prove that for a Stirling Cycle, the net work transfer is always from the system to the surroundings.
Determine the volume of chamber : the entire assembly is placed in an environment whose temperature is 200c. determine the volume of chamber 1 when thermodynamic equillibrium has been estabilished.
How may 84dollar payments will be required : a motorcycle is for sale for $2600. the dealer is willing to sell it on the folowing terms: No downpayment; pay $44 at the end of each of the first 4 months; pay$84 at the end of each mont after that until the loan has been paid in full.
Research the mark cubans insider trading scandal : Find an example when an organisation took up too much risk and was unable to cope with it. Give a short summary of the situation and also provide your own comments onhow did the company's managers handled the situation? Either defend them or prose..
Define a certain type of chemical bonding : Explain why the wild horse analogy can be used to help explain a certain type of chemical bonding
Calculate the temperature of the gas in the tank : comment on any safety hazards that might be encountered. especially, what would you anticipate if the inlet gas control valve were to malfunction and the gas space above the fuel were to reach full storage tank pressure (69bar)? the fuel tank has ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd