Determine the volume and height of the cooling tower

Assignment Help Mechanical Engineering
Reference no: EM13711554

A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit cross sectional area of the cooling tower is [(mdot)a /A ]=1800 lbm/hr ft^2. Determine the volume and height of the cooling tower, effectiveness and relative humidity.

Reference no: EM13711554

Questions Cloud

Determine the heat transfer for the process : A closed system of mass 10 kg undergoes a process during which there is energy transfer by work from the system of 0.147 kJ/kg, an elevation decrease of 50 m, and an increase in velocity from 15 m/s to 30 m/s. The specific internal energy decreases b..
The rate of heat transfer from the air to the walls is small : A 1.5 kilowatt heater is to be used to heat a room with dimensions 3.5 m × 5.0 m × 3.0 m. There are not heat losses from the room, but the room is not airtight, so that the pressure in the room is always atmospheric. Consider the air in the room to b..
Determine the specific internal energy at the final state : A vertical piston/cylinder device contains 0.01 lbm of gas. The initial gas volume is 0.18 ft3 and the initial specific internal energy is 282 Btu/lbm. The piston, with a mass of 110 lbm and cross-sectional area of 0.11 ft2, is in equilibrium with th..
Find the reservoir that the stream of water exiting nozzle : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..
Determine the volume and height of the cooling tower : A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit c..
Torsion and direct compression in the base of the boom : A work platform is elevated on the end of a boom that has the ability to extend its length and vary its angle with respect to the ground. The platform width is large compared to the boom diameter so that it is possible to load the boom eccentrically ..
Determine net rate of heat transfer for ambient reservoir : A heat pump supplies 40 kW of heat to maintain the inside of a house at 25 degree C in cold winter months when the ambient temperature is 00C. Power required to operate the heat pump cycle is provided by a heat engine cycle which receives 10 kW of he..
Determine the velocity of the air at the inlet : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. The inlet cross-sectional area is 6 cm 2 . At the duct exit, the pressure of the air is 100 kPa and..
Streams of cold and warm air are mixed to get air : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8 degree C and 100 kPa at a rate of 0.55 m3/s and warm air enters at 30 degree C and 10..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the maximum available friction force

A block weighing 80 N is resting on a plane inclined 20 degree to the horizontal. The coefficient of static friction is 0.5. Determine the friction force on the block. What is the maximum available friction force?

  If it has to be operated in 300degf maximum with fully

a forged 6061-t6 aluminum bar d1.5 in. with sut45000 psi will be used for one of the machine component. if it has to be

  The specific internal energy after expansion is 230 kjkg

the gases in the cylinder of an internal combustion engine have a specific internal energy of 800 kjkg and a specific

  When the input is 100 kpa the output is 5 mv and when the

a pressure sensing device has an electrical output and is approximately linear. when the input is 100 kpa the output is

  Find the maximum tangential stress maximum radial stress

a grinding wheel is designed to run at 1800 rpm and has a weight of 2.3 lbf. if the grinding wheel has a thickness of

  What is the difference between the pressure inside a soap

what is the difference between the pressure inside a soap bubble and atmospheric pressure for a 3-in-diameter bubble?

  The density of the truncated cone is 4000 kgm3 and the

the rigid body shown above is made of a solid truncated cone and solid hemisphere joined together at the bases of the

  What is the work input requirement for the pump what is the

consider a steam power plant that operates on a simple ideal rankine cycle and has a net power output of 45 mw. steam

  A full-revolution press has 100 rpm flywheel rotation the

a full-revolution press has 100 rpm flywheel rotation. the press is equipped with two-hand palm buttons mounted on the

  This type of device is isobaric assume the device is

a de-superheater works by injecting liquid water at 20 degrees c into a 10 kgs stream of superheated water vapor at 300

  Determine the discharge temperature and the power required

a steady flow steady state air compressor handles 4000 ft3min measured at the intake state of 14.1 psia 30.0degf and a

  Considering the maximum normal stress theory

A machine component of square cross- section is subjected to a direct tensile of 20 kn and a shear load of 10 kN. Considering the maximum normal stress theory and distortion energy theory of failure calculate the dimension of the component. Take fact..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd