Determine the velocity ms and mass flow rate kgs of the

Assignment Help Mechanical Engineering
Reference no: EM13637602

Ammonia enters a control volume at a temperature of 150°C and a pressure of 16.0 bar. The incoming volumetric flow rate is 10 m3/s through a pipe that is 0.5 m in diameter. The ammonia is cooled in the device and exits either as a saturated liquid at 6.0 bar or saturated vapor at 6.0 bar. The saturated vapor exits through a pipe with a diameter of 0.5 m. The mass flow rate of saturated liquid ammonia exiting the control volume is measured to be 20 kg/s. The saturated liquid leaves through a pipe 10 cm in diameter. Assume steady state and uniform flow at each inlet or exit.

a) Determine the velocity (m/s) and mass flow rate (kg/s) of the ammonia saturated vapor stream leaving the control volume.

Reference no: EM13637602

Questions Cloud

Determine the fraction of the heat transfer qh discharged : a reversible heat pump cycle operates between hot and cold reservoirs at th 27degc and tc -3degc respectively.
A gas is compressed from an initial volume of 575l to a : a gas is compressed from an initial volume of 5.75l to a final volume of 1.24 l by an external pressure of 1.00 atm.
What is the approach to determining the difference between : 1. demonstrate the difference between a high value of f-factor and a low-value. what conclusion can you draw from
How well do exams given during the semester predict : how well do exams given during the semester predict perfomance on the final? one class had 3 tests during the semester.
Determine the velocity ms and mass flow rate kgs of the : ammonia enters a control volume at a temperature of 150degc and a pressure of 16.0 bar. the incoming volumetric flow
I the electroysis of an aqueous solution agno3nbsp067gof : in the electroysis of an aqueous solution agno3nbsp0.67gof agis deposited after a certain period of time. what is the
Pseudoepedrine to metamphetamine the entire mechanism with : pseudoepedrine to metamphetamine? the entire mechanism withthe substitutions and movement of electrons with explanation
A football is kicked straight up into the air it hits the : a football is kicked straight up into the air it hits the ground 5.4s later.what was the greatest height reached by the
If the initial pressure of nh3gnbspis 7845 atmcalculate the : if the initial pressure of nh3gnbspis 7.845 atmcalculate the of nh3gnbspleft over after the reaction reaches

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd