Determine the values of the friction factor corresponding

Assignment Help Mechanical Engineering
Reference no: EM13614480

Chemical, Civil and mechanical engineers must often determine the power required to pump a fluid through a series of pipes. To do so, we must first determine a friction factor. If the fluid flow is turbulent and the pipes are smooth, the friction factor can be determined as.

1.1513/squrt(f) = ln(Re*squrt(f)/2.51

In this equation f represents the frinction factor, a positive value that does not exceed 0.1, and Re represents the Reynolds number, which is a function of the fluid properties, the pipe diameter, and the nominal fluid velocity. The reynolds number increases with increasing fluid velociyt. The flow becomes turbulent at higher velocities, when the Reynolds number exceed approximately 3000. Hence the above equation is valid only when Re exceed 3000.

Determine the values of the friction factor corresponding to Reynolds numbers of 5000, 12000, 20000. Does the frinction factor increase or decrease as the Reynolds number increases?

Reference no: EM13614480

Questions Cloud

For the following z-acoresm determine the percentage of : for the following z-acoresm determine the percentage of scores that lie beyond z show workingstandard
The income statement of a corporation for the month : the income statement of a corporation for the month ofnovember indicates a net income of 200000. during the sameperiod
Calculate the power required to run the refrigerator : the fluid used is r-134a. the flow of r-134a is 70 lbmmin. if r-134a enters a compressor at -10 deg f and is a
Given below are two applications of statistics descriptive : given below are two applications of statistics descriptive and inferential. choose what type of application is being
Determine the values of the friction factor corresponding : chemical civil and mechanical engineers must often determine the power required to pump a fluid through a series of
Widgets inc uses the straight-line method to depreciate : widgets inc uses the straight-line method to depreciate assets in determining its finacials profit. widgets also
Determine the reduction in the exit temperature of the : the compression stages in the axial compressor of the industrial gas turbine are close coupled making intercooling very
As reported by a spokesperson for southwest airlines the : as reported by a spokesperson for southwest airlines the no-show rate for reservations is 16. in other words the
Big lake boat tours sold off one of their tour boats that : big lake boat tours sold off one of their tour boats that was toosmall to meet the current needs of business.the boat

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Liquid water is cooled at a constant pressure of 200 kpa in

liquid water is cooled at a constant pressure of 200 kpa in a piston-cylinder device from a temperature of 110 degc to

  The body starts from the position sx0i with initial speed

the acceleration of a particle moving along a straight line is inversely proportional to its speed with the constant of

  Determine the air velocity

the air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. if the air is at 13.4 psia absolute and 70 degrees C and the reading of the differential pressure gage is 0.15 psi, determine the air velocit..

  Prepare a case study based industrial visit report

Overview of the company which includes company background, major businesses, annual production, and major customers involved.

  Carry out a simple thermodynamic analysis of this process

current automotive air conditioners use r134a as a working fluid. assume an evaporator temperature of 0c in practice

  Take cut off ratio 2 find the temperature after the end

a diesel cycle works on compression ratio of 18 and temperature at the start of compression is given as 300k. take cut

  When the input is 100 kpa the output is 5 mv and when the

a pressure sensing device has an electrical output and is approximately linear. when the input is 100 kpa the output is

  Define geometric angle of attack

Geometric angle of attack, The Piper Cherokee has a wing area of 170 ft2 and a wing span of 32 ft. Its maximum gross weight is 2450 lbs. The wing uses a NACA 65-415 airfoil, which has a lift slope of 0.10331deg^-1 and alpha(L=0)= -3.0deg. Assume th..

  The diffusion constant do and activation energy q of c in

the diffusion constant do and activation energy q of c in bcc fe is 0.01 cm2sec and 80kjmol respectively. in fcc fe the

  The same rod is now subjected to a torque of 8 kip-ft what

1. a circular stainless steel rod is subjected to an axial load of 10 kips. what diameter must the rod be to have a

  Steam enters at 300c and exits as liquid water at 90c while

a stream of methanol vapor is used to chill a countercurrently flowing saturated steam in an adiabatic heat exchanger.

  A tube with elastic modulus of 75 gpa is used to support a

a tube with elastic modulus of 75 gpa is used to support a compressive load. it is required that this tube must not

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd