Determine the value of force when the rod begins to yield

Assignment Help Mechanical Engineering
Reference no: EM13212537

A 20-mm diameter rod made of a ductile material with a yield strength of 350 MPa is subjected to torque of 100 N.m and a bending moment of 150 N.m. An axial force is then gradually applied. Determine the value of force when the rod begins to yield. Solve the problem two ways using the (a) Tresca theory (Maximum shearing stress theory) and (b) von Mises theory (Maximum distortion energy theory).

Reference no: EM13212537

Questions Cloud

Implications of planning and control : Discuss additional behavioral implications of planning and control when a company's management employs an imposed budgetary approach and a participative budgetary approach.
What technology do economists use to refer to the process : Money deposited for a term is not left in bank vaults but is loaned out by the banks (subject to mininum cash reserve requirements). This means that a dollar on deposit can flow back into the banking system one or more times.
Calculate the largest semicircular surface flaw oriented : calculate the largest semicircular surface flaw oriented along the axis of the bores that could withstand a fluid pressure of 50MPa.
Determine the air velocity : the air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. if the air is at 13.4 psia absolute and 70 degrees C and the reading of the differential pressure gage is 0.15 psi, determine the air velocit..
Determine the value of force when the rod begins to yield : A 20-mm diameter rod made of a ductile material with a yield strength of 350 MPa is subjected to torque of 100 N.m and a bending moment of 150 N.m. An axial force is then gradually applied. Determine the value of force when the rod begins to yield..
Compute k at the temperature for the reaction : equilibrium contains 2.4 moles of Cl2, 1.0 mole of NOCl, and 4.5 x 10-3 moles of NO. Calculate K at this temperature for the following reaction
Compute the expected annual savings and expected pw : A new engineer is evaluating whether to use a larger-diameter pipe for a water line. It will cost $350,000 more initially, but it will reduce pumping costs. The optimistic, most-likely, and pessimistic projections for annual savings are $30,000, $..
Determine the stresses and strains in the bar : Also determine the axial force and deformation of the diameter due to temperature rise. Let E = 120 GPa and Co-efficient of linear thermal expansion = 0.0000168 per °C.
What is the probability of observing a sample mean : As part of a marketing study, the food king supermarket chain has randomly sampled 150 customers. the average dollar volume purchased by the customers in this sample was $31.14, that is , the sample mean from a sample of size 150 was $31.14.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd