Determine the uncertainty of the velocity measured when the

Assignment Help Mechanical Engineering
Reference no: EM13610890

a) Steady, frictionless air, at 100 kPa and 25 C, flows in a horizontal duct that has a cross sectional flow area reduction in it. The reducer smoothly forms the 18 cm diameter duct to a 10 cm duct. A U-tube water manometer connects on both ends of the reducer component and shows a liquid difference level of h = 8 cm. The flow in the larger 18 cm duct is considered to be moving very slowly compared to the 10 cm duct flow. Adapt Bernoulli's and ideal gas equations to determine the flow's velocity in the smaller duct. (b) Note that the velocity is proportional to the square root of the manometer reading {i.e. V=k*h^0.5}where k is a proportionality constant. And uncertainty is the differential of the velocity divided by the velocity {dV/V} Determine the uncertainty of the velocity measured when the uncertainty of the manometer reading is +/- 2mm. R = 0.287 kPa*m^3 / kg*K water density = 1000 kg/m3

Reference no: EM13610890

Questions Cloud

Determine a the boundary work needed for this process and : a piston cylinder device contains 2.5 kg of carbon dioxide co2 initially at 100 kpa and 300 degrees celsius.the co2 is
Specimens of blood from 10 different animals were analyzed : specimens of blood from 10 different animals were analyzed for blood count say y in units of 100 and packed cell volume
Bob and lisa must replace their old car as soon aspossible : bob and lisa must replace their old car as soon aspossible. they have found a new one that meets their needsand have
Note that a sometimes called the footprint of the object : a shape that covers an area a and has a uniform height h has a volume v ah. a show that v ah is dimensionally
Determine the uncertainty of the velocity measured when the : a steady frictionless air at 100 kpa and 25 c flows in a horizontal duct that has a cross sectional flow area reduction
Find assuming ney l x b0nbsp b1x1nbspthe least squares : the relationship assumed linear between yield of bourbon y and aging time x was studied by observing yields yi from
The moment you pass the police car you realized that you : on your way to classes you are driving on 8th street at a speed of 60 mph 26.8 ms when you see a police car parked at
Production overheads are absorbedinto production units by : production overheads are absorbedinto production units by the use of overhead cost rates. which ofthe best describes
Study appendix3 richard ellis the director of cost : study appendix3. richard ellis the director of cost operations of american microdevices wishes to develop anaccurate

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the radius of curvature of the trajectory

Coal is discharged from the tailgate of a dump truck with an initial velocity vA = 2 m/s A 50°. Determine the radius of curvature of the trajectory described by the coal.

  You have a bevel gear and shaft and you have to find the

you have a bevel gear and shaft and you have to find the maximum load that can be applied on it. what type of

  Determine the bolt stiffness

Determine the bolt stiffness, the tube stiffness, and the joint constant C.

  What is the average air pressure exerted on the piston

homebuilding has undergone significant advances in the last 20 years due largely to replacement of hand tools hammers

  How is the technology utilized effectively

How is the technology utilized effectively or ineffectively? What are some barriers to more effective usage, and what are some recommendations you would make to overcome these barriers?

  1 consider the diagram below where a pump is used to draw

1 consider the diagram below where a pump is used to draw water from a lake to feed an irrigation system.a which of the

  The velocity is 20 ftsec after the 200 pipe run this 6 pipe

a 6 nominal pipe size schedule 40 pipe hase a chamfered entrance and 200 ft long. the velocity is 20 ftsec. after the

  Determine an expression for the number of cycles to failure

Determine an expression for the number of cycles to failure, Nf if the initial crack size is a0. State any assumptions you make.

  What would happen if the air filter was partially choked

What would happen if the air filter was partially choked. If the piston rings were leaking state what you would expect the results of a, b, c, and d above would be.

  Determine the work kj performed by the piston on the

initially 0.05 kg of air is contained in a piston-cylinder device at 200 degc and 1.6 mpa. the air then expands at

  Determine the change in the internal energy of the system

nitrogen at 100c and 600 kpa expands in such a way that it can be approximated by a polytropic process with n 1.2.

  Control engineeringyou have to design a control system for

control engineeringyou have to design a control system for an annealing furnace. the furnace is used to anneal special

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd