User Account

All Pages

Determine the total number of rivets required

Assignment Help Mechanical Engineering
Reference no: EM131123060

A double strap butt joint had to carry a load of 17kN. the ultimate shear strength of the rivets used is 260MPa and a factor of safety of 8 is to apply. if the rivet diameters are to be 6mm, determine the total number of rivets required.

Reference no: EM131123060

Questions Cloud

Calculate the percent ionization of 8.0×10-3 m : Calculate the percent ionization of 8.0×10-3 M butanoic acid in a solution containing 8.0×10-2 M sodium butanoate.
Determine the mass rate of flow : Water flows steadily into a tank through pipes 1 and 2 and discharges at steady rate out of the tank through pipes 3 and 4. Determine the mass rate of flow and the discharge from pipe 4, and the maximum velocity in pipe 4
Discuss the functions and advantages of using ehrs : Discuss the functions and advantages of using EHRs. Discuss three to four forms used to keep patient information in EHRs. What is the purpose of each form?
Used machines from freeman incorporated : At the beginning of the year, Grillo Industries bought three used machines from Freeman Incorporated. The machines immediately were overhauled, installed, and started operating. Because the machines were different, each was recorded separately in ..
Determine the total number of rivets required : A double strap butt joint had to carry a load of 17kN. the ultimate shear strength of the rivets used is 260MPa and a factor of safety of 8 is to apply. if the rivet diameters are to be 6mm, determine the total number of rivets required
Left ventricular assist device a destination therapy : Assignment 1:-Left ventricular assist device- A destination therapy Assignment 2: Bioinformatics assignment
With which velocity both the balls move after impact : If there are two balls of equal mass and of perfectly elastic material are lying on the floor. One of the ball with velocity v is made to struck the second ball. With which velocity both the balls move after impact
Explain possible reason for the turnover costs and possible : Explain a possible reason for the turnover costs and the possible implications of the data for human resource professionals and organizations. Provide at least one potential solution for reducing turnover rate that could enable an organization to ..
What will be the heat supplied : If the output of a gas turbine is 300 KW and its efficiency is 20 percent, what will be the heat supplied

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The incoming air velocity is 100 ms the air density and

consider airflow past a sphere of diameter 5 cm. the incoming air velocity is 100 ms. the air density and temperature

  Compute the heat transfer-methane flows with the velocity

At a section where the diameter is 4 in, methane flows with the velocity of 50ft/s and a pressure of 85 psia. At a downstream section, where the diameter has increased to 6 in, the pressure is 45 psia. Assuming the flow to be isothermal, compute the ..

  It heat is supplied continuously during the process in

dry saturated steam at 7 bar expands reversibly in a cylinder behind a piston until the pressure is 0.1 bar. it heat is

  If the angle is big there must be a lot of tension thus as

in the bird-on-a-wire group work example how do you expect the angle and tension to be related? remember that this is

  Determine the rate of heat loss from the pipes

determine the rate of heat loss from the pipes and other components, and calculate the thermal efficiency of the plant.

  Heat source for a vapor power cycle of a power station

At a particular location a hot spring is available to provide a heat source for a vapor power cycle of a power station and not far away a melt water river from a glacier is available to provide a heat sink. the hot spring has a flow of 1500 liters/se..

  A particle moves along a straight line with an

a particle moves along a straight line with an acceleration of a 53s13 s52ms2 where s is in meters. determine the

  Reservoir elevation and discharge into the channel

The slope of the channel is 0.0020 ft/ft. Compute a chart showing the relationship be- tween reservoir elevation and discharge into the channel.

  Predict the discharge of a larger geometrically similar

a small model of a pump is tested in the laboratory and found to have a specific speed n equal to 1000 when operating

  Calculate the energy requirement to heat 100 lb water from

calculate the energy requirement to heat 100 lb water from 100 f to 90 c in btu. if an electrical heating element is

  Use muller method to determine the real and complex roots

use muller method to determine the real and complex roots offx x3 - x2 3 x - 2fx x4 - 2 x3 5 x2 - x - 10and write a

  Does this mean that f is a conservative force

Does this mean that F is a conservative force? Give reasons for your answer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd