Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a non-pipelined chip in which each instruction can be executed in 140 ns. A chip design company comes up with a new 4-stage pipelined design to execute instructions such that stage s1 takes 30 ns, s2 takes 30 ns, s3 takes 50 ns and s4 takes 30 ns of processing time.
a. Determine the time taken to execute the first instruction I1 in both the pipelined and non-pipelined cases. Also determine the time (i.e., how long it takes to execute them) at which the second instruction I2 and third instruction I3 finish execution in the pipelined and non-pipelined cases. Explain your answer.
b.Next, given the above conditions determine the maximum possible speedup in the throughput of the pipelined machine over the non-pipelined version. Explain your answer.
Find the maximum acceptable propagation loss for the system, given that the transmit power at the base station is 30W, base station feeder losses are 15 dB, the base station antenna gain is 6 dB, the mobile antenna gain is 0 dBi and the mobile fee..
A 60-watt outdoor lightbulb is advertised as having an average life (i.e. MTTF) of 1,000 operating hours. However, experience has shown that it will also fail on demand an average of once every 120 cycles.
In a swamped common-emitter BJT amplifier, as shown below, if Vcc = 12 V, R1 = 8.2 k , R2 = 10 k , Rc = 500 , RE = 1 k , VBE = 0.7 V, and = 100, what is the transistor's emitter current
An alarm is powered by 120 VAC, and the on/off state of the alarm is controlled by an EM relay. Design the interface between a computer output port and the EM relay. The dropout voltage is 3.5 V, and the coil current needs at least 100 mA.
A rifle is aimed horizontally at a target 50.0 m away. The bullet hits the target 2.00 cm below the aim point. A. What was the bullet's flight time B. What was the bullet's speed as it left the barrel
A 3 phase, 208V, 4 pole, 60Hz, Y connected synchronous generator has a synchronous reactance of 8 ohm. Assume the resistance of this generator is negligible. The machine terminal voltage is maintained constant at 208V (line to line).
A 3-phase motor has coils wchich can be configured in a Y load. If each load phase has an impedance of 8+j6 ohms determine the power taken by the motor when supplied by a balanced 3-phase voltage source of 440V line to line.
a certain ideal voltage generator is characterized as v(t) = 40 sin 377 t . If this generator is measured with a DC voltmeter, the instrument reads 12 volts, what is the rms value of this voltage waveform
An Australian emu is running due north in a straight line at a speed of 13.0 m/s and slows down to a speed of 10.5 m/s in 3.60 s. (a) What is the magnitude and direction of the bird's acceleration
1- Why do we use PWMCTL What does it mean If we have PWMCTL=0x80 What does it mean if we have PWMCTL = 0x00 2- The PWMPER register and PWMDTY registers are 8 bits. What does it mean when we say we are using a 16-bit PWM
Design a circuit that, given a 2-bit value, will light a LED corresponding to that value. One of four LEDs should be lit for each of the four possible input values (binary 0 through 3).
What are the design implications for the location and positioning of solar cells? Explain why the use of solar cells might be more appropriate in some regions of the country.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd