Determine the tension in cables de and df

Assignment Help Mechanical Engineering
Reference no: EM13217543

a 600-lb crate hangs from a cable that passes over a pulley B and is attached to a support at H. The 200-lb boom AB is supported by a ball-and-socket joint at A and by two cables DE and DF. The center of gravity of the boom is located at G. Determine (a) the tension in cables DE and DF, (b) the reaction at A.

Reference no: EM13217543

Questions Cloud

How many positive impulses will be counted per second : A magnetic pickup is used to detect the shaft speed of a turbocharger. A standard hexagonal nut is used to excite the pickup. If the shaft is turning at 50,000 rpm, how many positive impulses will be counted per second?
Educational change process-initiation-implementation : Describe the three phases of the educational change process including initiation, implementation and institutionalization according to Michael Fullan.
Define the migration of health professionals : As an ethical matter, do wealthy destination countries bear responsibility for the migration of health professionals and for the effects of that migration on developing countries?
Evaluate the total ending inventory : According to the production plan, what will be the total ending inventory in the second month after the second month's demand is satisfied and what level of anticipation inventory would be needed at the start of the first month to result in an end..
Determine the tension in cables de and df : The center of gravity of the boom is located at G. Determine (a) the tension in cables DE and DF, (b) the reaction at A.
Compute the number of kilograms of hydrogen : Assume a diffusion coefficient of 1 × 10-8 m2/s, that the concentrations at the high- and low-pressure sides of the plate are 2.4 and 0.6 kg of hydrogen per cubic meter of palladium, and that steady-state conditions have been attained.
Plot wind speed against height on linear : for a neutral surface layer, plot wind speed against height on linear and on semi-log graphs for friction velocity of .5 m/sec and aerodynamic roughness length.
What is the survey method : Which survey method (mail, telephone, or personal interview) would you use for the following situation? Explain your choice.
Describe what is motivating employees : What theories and/or studies could be applied here to better understand what is motivating employees at Listo Systems? Remember to consider all of the theories

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  Determine the rate of recrystallization

It is known that the kinetics of recrystallization for some alloy obey the Avrami equation, and that the value of n in the exponential is 8.4. If, at some temperature, the fraction of recrystallization is .30 after 100 min, determine the rate of r..

  Determine the absolute maximum bending stress in the beam

If the beam has square cross section of 9 in., on each side, determine the absolute maximum bending stress in the beam.

  What is discharge revised discharge pressure of compressor

What is the discharge revised discharge pressure (guage pressure) of the compressor ?  Is the assumption of change in temperature valid for calculating the discharge pressure of the compressor ?

  Find the orthogonal rake angle of the cutting tool

the friction force acting at the chip-tool interface the main (tengential ) cutting force is 1500N . Find the orthogonal rake angle of the cutting tool?

  Explain coefficient reaction

Coefficient Reaction, The removal efficiency of a reactor tank is 73-percent and its residence time is 28.5s

  Calculate how many pounds of strawberries are needed

To make strawberry jam, crushed strawberries and sugar are mixed in a 45:55 mass ratio, and the mixture is heated to evaporate water until the residue contains one-third water by mass. Calculate how many pounds of strawberries are needed to make a..

  Calculate the outlet temperature

A compressor operating adiabatically is to compress 2.83 m^3/min of air at 29.4C and 102.7 kN/m^2 to 311.6kN/m^2. Calculate the power required if the efficiency of the compressor is 75%. Also, calculate the outlet temperature.

  Specify a diameter d using a design factor of nd

xerted on the shaft shown in the figure, which rotates at 1150 rev/min and supports a 10-kip bending force. Use a 1095 HR steel. Specify a diameter d using a design factor of nd = 1.6 for a life of 3 min. The surfaces are machined.

  Determine the diameter of the shaft using tresca

Determine the diameter of the shaft using TRESCA and Von Mises-Henky failure

  Explain entropy generation in a steam turbine

Entropy Generation in a Steam Turbine, Steam at a rate of 15lbm/s enters a turbine at 500 Psia, 800f and exits at 5 Psia. For a reversible, adiabatic process (iseentropic)

  Determine the reactions of simply supported

Determine the reactions of simply supported beam to both a concentrated and uniform load. A beam with a span of 21 ft is simply supported at the left-hand end and fixed at the right-hand end.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd