Determine the steady-state temperature distribution in the

Assignment Help Mechanical Engineering
Reference no: EM13644149

The edges of a thin plate are held at the temperature described below. Determine the steady-state temperature distribution in the plate. Assume the large flat surfaces to be insulated.

If the plate is lying along the x-y plane, then one corner would be at the origin. The height of the plate would be 1m along the y-axis and the length would be 2m along the x-axis. The edge along the y-axis is being held at 0 C. The edge along the x-axis is being held at 0 C. The edge parallel to the x-axis is being held at 0 C. The edge parallel to the y-axis is being held at 50sin(pi*y) C.

 

Reference no: EM13644149

Questions Cloud

The 13c nucleus is a spin 12 particle which means it can : the 13c nucleus is a spin 12 particle which means it can orient in two directions in a magnetic field with the field
Theater surface is exposed to air that is also at 20 : a cartridge electrical heater is shaped as a cylinder of length l200 mm and outer diameter d20 mm. under normal
Under conditions for which the air maintains an average : the case of a power transistor which is of length l10mm and diameter d12mm is cooled by an air stream of temperature
A 1553 g sample of chymotrypsin is placed into 1000 ml of : a 1.553 g sample of chymotrypsin is placed into 100.0 ml of water. when this solution was separated from pure water by
Determine the steady-state temperature distribution in the : the edges of a thin plate are held at the temperature described below. determine the steady-state temperature
What two families of elements in the periodic table : what two families of elements in the periodic table generally do not accept additional electrons i.e. which ones have
Contrast the chase demand adjusting internal resources to : contrast the chase demand adjusting internal resources to match changes in demand and the level resource shifting and
If the average speed of an oxygen molecule is 4280 cmsec : if the average speed of an oxygen molecule is 4280 cmsec at 25c what is the average speed of carbon dioxide molecule at
Argon gas is ten times denser than he gas at the same : argon gas is ten times denser than he gas at the same temperature and pressure. which gas is predicted to effuse

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider the reversible adiabatic flow of stream through a

consider the reversible adiabatic flow of stream through a nozzle. steam enters the nozzle at 1 mpa and 300degc with a

  Determine the steady-state solution for the following

determine the steady-state solution for the following differential equations. if resonance exists for the equations

  Water at 20c flows through at 10cm inner dyameter pipea

water at 20c flows through at 10cm inner dyameter pipe.a static pressure tap of a pilot tube at a cross section

  Determine a the mass flow rate of the refrigerant b the

a heat pump using r-134a as its working fluid is used to keep a space at 25degc by absorbing heat from geothermal water

  Steam at 200 c and 7 bars enters a mixing tank at a rate of

steam at 200 c and 7 bars enters a mixing tank at a rate of 3 kgmin through a pipe with a cross-section of 1.20 cm2.

  One jet is at 400 k and 100 ms and the other is at 200 k

two jets of air of equal mass flow rate mix thoroughly before entering a large reservoir. one jet is at 400 k and 100

  Determine the normal stress developed in the tube and rod

the magnesium alloy modulus of elasticity e 44.7 gpa coefficient of thermal expansion 2610-6oc tube ab is capped with

  If the x component of acceleration is a14t2ms2 where t is

a rocket is fired from rest at x0 and travels along a parabolic trajectory described by y2120103xm. if the x component

  A for a supply air volumetric flow rate of 40m3 min

at a steady rate moist air is to be supplied to a classroom at a specified volumetric flow rate and temperature t. air

  Draw free body diagram - shear and moment diagrams

Determine if the shaft has infinite fatigue life. If not, determine the number of cycles to failure. Also determine the safety factor for first cycle yield and draw a free body diagram, shear and moment diagrams, and graph the loads on the shaft..

  Find the discharge coefficient for flange taps

the reynolds number of a fluid flowing through a 5-cm-diameter, square-edged orifice plate meter within a 15-cm pipe is 250,000. Find the discharge coefficient for flange taps.

  A round casting is 01 m in diameter and 5 m in length what

a round casting is 0.1 m in diameter and .5 m in length. another casting of the same metal is elliptical in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd