Determine the static head efficiency required of the

Assignment Help Mechanical Engineering
Reference no: EM13636330

In an automotive gas turbine the centrifugal compressor is driven at 40,000 rpm by an axial turbine. The compressor impeller is 180 mm dia. With radial vanes and there is no inlet swirll the slip factor is 0.9 and the isentropic efficiency is 80% If there is a 5% loss in total pressure in the intervening combustion system in where the air is heated to 950C, determine the static head efficiency required of the turbine if the total pressure of its exhaust is not to be less than 1.6 bar and the exhaust velcotiy is 300 m/s. Ambient condition are 300K and 1 bar, and for air take Cp=1.01 kj/Kg K and sp. Heat ratio = 1.4, formthe gases take Cp= 1.15 kJ/kgK and sp. Heat ratio = 1.33.

Reference no: EM13636330

Questions Cloud

A 66 cm diameter pipe gradually narrows to 40 cm when water : a 6.6 cm diameter pipe gradually narrows to 4.0 cm. when water flows through this pipe at a certain rate the gauge
How would the wheel diameter and the volumes of the : the minto wheel is a power-producing device activated by evaporating and condensing a working substance. the only
The round table of astrologists consists of 144 people as : the round table of astrologists consists of 144 people. as they examine the laws of the stars they find that it brings
Two charged concentric spheres have radii of 96 and 151 cm : two charged concentric spheres have radii of 9.6 and 15.1 cm. the charge on the inner sphere is 4.09 multiplied by 10-8
Determine the static head efficiency required of the : in an automotive gas turbine the centrifugal compressor is driven at 40000 rpm by an axial turbine. the compressor
Find the uncertainty in position in nm associated with : find the uncertainty in position in nm associated with anelectron that is moving with a velocity of 274 kms.
A hydrogen-filled blimp cruises slowly at a low altitude : a hydrogen-filled blimp cruises slowly at a low altitude. its maximum useful payload including crew and cargo is 6857
Why do we use 11 equivalentsof bromine solution in the : why do we use 1.1 equivalentsof bromine solution in the reaction of trans-stilbene with brominein dichloromethane ?
As the sample size increases the width of the interval : samples of two different types of automobiles were selected and the actual speed for each car was determined when the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd