Determine the stability of the closed-loop system

Assignment Help Electrical Engineering
Reference no: EM13248460

The loop transfer function L(S) of a single-feedback-loop control system is given below. Sketch the Nyquist plot of L(jw) for w=0 to w=infinity, Determine the stability of the closed-loop system. Solve for the intersect of L(jw) on the negative real axis of the L(jw)-plane analytically.
L(S) = 20/[s(1 + 0.1s)(1 + 0.5s)]

Reference no: EM13248460

Questions Cloud

Define positive direction in the forward direction : You drive your 1,345-kg car at a constant speed of 23 mph a distance of 71 m down a ramp that has a grade of 14 %. Define positive direction in the forward direction
Determine the sum or difference of two numbers : Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.
What component of the project plan will help you : What component of the project plan will help you determine how to manage this request for new requirements? Explain how this component is used to manage project changes.
Determine the second ball after the collision : A 4.4kg ball with a velocity of 5.0m/s in the+x-direction collides head-on elastically with a stationary 2.5kg ball. What is the speed of the second ball after the collision
Determine the stability of the closed-loop system : The loop transfer function L(S) of a single-feedback-loop control system is given below. Sketch the Nyquist plot of L(jw) for w=0 to w=infinity, Determine the stability of the closed-loop system.
How much fuel is required to spin up the asteroid : Consider Iron asteroid (density 7900 kg/m^3) shaped like a cylinder 5.0 km long and 3.0 km in diameter, How much fuel is required to spin up the asteroid
Describe its competitive advantage using the resource-based : Pick a publicly traded company. Describe its competitive advantage using the resource-based model of above average returns.
Compute the heat change at 100 degrees celsius : calculate the heat change at 100 degrees Celsius and indicate whether heat was absorbed or released: a) joules to condense 10.0 g of steam; b) kilojoules to condense 76.0 g of steam; c) joules to vaporize 44.0 g of water; d) kilojoules to vaporize..
Calculate the initial and final kinetic energy of the system : A student on a piano stool rotates freely with an angular speed of 3.10 rev/s. The student holds a 1.40-kg mass in each outstretched arm, 0.759 m from the axis of rotation, Calculate the initial and final kinetic energy of the system

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the component of q at p in the direction of pt

(a) Determine a unit vector in the direction of Q at P(1, 2, 1) (b) Find the component of Q at P in the direction of PT where T is point (5, 3, -4) (c) Where is Q the same as the unit vector of  \(a_{x}+11a_{y}+10a_{z}\)

  What is hall electric field is measured in the y direction

Show that the Hall coefficient for a p-type semiconductor is R_H=1/pe where p is the hole concentration and e is the electron charge. Assume the current is along the +x direction, the magnetic field is along the +z direction, and the Hall electric..

  Find the damping ratio and undamped natural frequency

How to find the damping ratio and undamped natural frequency given a 2nd-order differential equation.

  Model a discrete-time system

To understand di erent signal models To be able to model a discrete-time system and design simple signal processing algorithms.

  Obtain microstrip realization for a dilecetric material

Design a five section high pass lumped element filter with 1 dB equal-ripple response, a cut-off frequency of 1 GHz and an impedance of 50 Ohms. Plot the amplitude and phase response of the filter.

  What is the gain of the filter at the cutoff frequency

(a) Design a high-pass filter with a cutoff frequency of 40 kHz. Use 0.01 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at the cutoff frequency Give your answer both as ratio (Vout/Vin..

  What is the time interval between samples

Telephone signals are typically sampled at 8000 Hz. a. What is the time interval between samples b. What is the highest frequency that can be recovered from a sampled signal

  Find an expression for the net current in the line

Two voltage waves of equal amplitude, V0, and frequency w, propagate in the forward z direction in a lossless transmission line of characteristic impedence Z0. One waves is phase-shifted from the other by \o radians.

  Find the frequency response of the system

For the system represented by the following difference equation y[n] = 0.5x[n] + 0.5x[n - 1] find: (a) the transfer function H(z) of the system. (b) the frequency response H(e^jw) of the system.

  Draw the sympol and truth table of the gate

draw the sympol and truth table of the gate that corresponds to the action of the logic gate.

  Draw the rom truth table for the seven segment

Draw the ROM truth table for the seven segment

  What is the percent quantization error

A unipolar 16 bit ADC measures 0 - 10 volts full scale.  What is the minimum resolvable voltage What is the percent quantization error What is the percent quantization error if a 1 volt max signal is input

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd