User Account

All Pages

Determine the smallest diameter that can be selected for rod

Assignment Help Mechanical Engineering
Reference no: EM13924131

A control rod made of yellow brass must not stretch more than 0.125 in when the tension in the wire is 800 lbs. Knowing that E = 15,000,000 psi and that the maximum allowable stress is 32 ksi (32,000 psi), determine

(a) the smallest diameter that can be selected for the rod

(b) the corresponding maximum length of the rod.

Reference no: EM13924131

Questions Cloud

Determine the expression for required torque : A solid cone of radius R and vortex angle 2θ is to rotate at an angular velocity, ω .An oil of dynamic viscosity µ and thickness ‘t' fills the gap between the cone and the housing. Determine the expression for Required Torque.
Describe how a semaphore can be used to act like a lock. : The loop should execute until a "shutdown" flag is set to true on the runnable object executing in the thread.
Describe the way manager use accounting information : Describe the way manager's use accounting information to create value in organizations. How do you use it in your personal life
Complete the company''s cash budget : Complete the company's cash budget for April in good form. Make sure to indicate what borrowing, if any, would be needed to attain the desired ending cash balance.
Determine the smallest diameter that can be selected for rod : A control rod made of yellow brass must not stretch more than 0.125 in when the tension in the wire is 800 lbs. Knowing that E = 15,000,000 psi and that the maximum allowable stress is 32 ksi (32,000 psi), determine the smallest diameter that can ..
Write methods that accept an array or list : Write methods that accept an array or list and returns lowest score, highest score, median score, average score and the standard deviation of the scores.
Determine the power produced : A small scale hydraulic power system has an elevation difference between the reservoir water surface and pond surface temperature downstream of turbine is 10m. The flow rate through the turbine is 1m^3/s. The turbine efficiency is 83%. Determine t..
Write a function which adds the two numbers : In C write a function which adds the two numbers. Test this function by calling from the main. In main, the user should be asked to provide the two numbers.
What are trade-offs involved when constructing a portfolio : Describe the difference between a price momentum strategy and an earnings momentum strategy.  What are the trade-offs involved when constructing a portfolio using a full replication versus a sampling method?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the nusselt number and the convective heat

calculate the nusselt number and the convective heat transfer coefficient for water at a bulk temperature of 32oc

  Question 1 bending about two axesthe load p 2 kn is

question 1 bending about two axesthe load p 2 kn is applied to the end of rectangular section cantilever beam shown

  Certain microalloyed steels contain small additions of

certain microalloyed steels contain small additions of vanadium or niobium that permit the grain size to be reduced to

  The length of the assembly shown decreases by 040mm when

the length of the assembly shown decreases by 0.40mm when an axial force is applied by means of rigid end plates.

  The flow rate of methyl acetate in the mixture is to be

a mixture of methanol and methyl acetate contains 15.0wt methanol. using a single dimensional equation determine the

  Required input power of the pump

For a discharge of Q ¼ 100 L=min and a loss across the pump of hL ¼ 7 m, what is the required input power of the pump if its ef?ciency is 78%?

  Determine a the mass flow rate through the nozzle b the

air enters an adiabatic nozzle steadily at 300 kpa 200 degree cesius and 30 ms and leaves at 100 kpa and 180 ms. the

  Determine the final temperature of the air in the cylinder

a frictionless piston-cylinder device fitted with stops above the piston contains 1.2 kg of air at 200degc and 700 kpa.

  How much pressure is required for a force output of 62275

1. how much pressure is required for a force output of 62275 newtons if the effective piston area of the cylinder is

  Gear a accelerates clockwise from rest to 100 rpm in 2

gear a accelerates clockwise from rest to 100 rpm in 2 seconds. determine the angular acceleration of gear b and the

  Which film of this paint could be spread on vertical wall

Acrylic latex paint can be described as a Bingham plastic with a yield stress of 200dyn/cm^2, a limiting viscosity of 50 cP, and a density of 0.95 g/cm^3. What is the maximum thickness at which a film of this paint could be spread on a vertical wall ..

  Nitrogen is compressed in a polytropic process with n 12

nitrogen is compressed in a polytropic process with n 1.2 from 120 kpa and 10oc to 800 kpa in a piston-cylinder

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd