Determine the slope and intercept of the line

Assignment Help Mechanical Engineering
Reference no: EM131083620

Palladium (II) forms an intensely colored complex at pH 3.5 with arsenazo III at 660 nm.33 A meteorite was pulverized in a ball mill, and the resulting powder was digested with various strong mineral acids. The resulting solution was evaporated to dryness, dissolved in dilute hydrochloric acid, and separated from interferents by ion-exchange chromatography. The resulting solution containing and unknown amount of Pd(II) was then diluted to 50.00 mL with pH 3.5 buffer. Ten-milliliter aliquots of this analyte solution were then transferred to six 50.00 mL volumetric flasks. A standard solution was then prepared that was 1.00×10-5 M in Pd(II). Volumes of the standard solution shown in the table were then pipetted into the volumetric flasks along with 10.00 mL of 0.01 M arsenazo III. Each solution was then diluted to 50.00 mL, and the absorbance of each solution was measured at 660 nm in 1.00-cm cells.

1311_6f5c7be6-d8de-4c32-8c70-762f359ce18c.png

(a) Enter the data into a spreadsheet. and construct a standard-additions plot of the data.

(b) Determine the slope and intercept of the line.

(c) Determine the standard deviation of the slope and of the intercept.

(d) Calculate the concentration of Pd(II) in the analyte solution.

(e) Find the standard deviation of the measured concentration.

Reference no: EM131083620

Questions Cloud

Discuss perspective on the relative influence of heredity : Discuss your perspective on the relative influence of heredity and environment--that is, which do you think has the greatest influence of the two after viewing the video above and reading this week's assigned learning material--and how your view ..
Research and collect data for decision making : Create a flowchart of the process to conduct research and collect data for decision making (which does not have to fit any specific process form; just make it clear).
Internal rate of return from switching to recliamed water : Suppose that Dr. Stone brewery could use recliamed municipal water waste water to make beer instead of the municipal water that is currently being used. this will help conserve limited fresh water resources and reduce the brewery's annual water bill...
Investment will be used to install new body shop : How many autos will Ford want to produce in its new Kansas City plant? Ford announced that it plans to invest $400 million over the next two years in its auto manufacturing plant in Kansas City as it prepares to build a new behicle there. the $400 mi..
Determine the slope and intercept of the line : Determine the slope and intercept of the line.
How do you believe we should study human behavior : How do you believe we should study human behavior? Who or what influenced your own thinking and understanding of the human mind and behavior? What are your major contributions to understanding the human mind and behavior?
Explanation of the organizational issues : a) Develop a clear explanation of the organizational issues within the case study. b) Outline a clear direction for the case study analysis that includes all of the elements you plan to include.
Urban public transportation systems : In the text, we suggested that for well-off individuals with uniform taxation, preferences for education were not single-peaked. Why might preferences for local parks and urban public transportation systems (e.g., buses and subways) also not be singl..
Question and the ensuing discussion : Share one new insight that you have had about U.S Employment Laws and Regulations from this material. In addition, respond to this question and the ensuing discussion: What are the implications of the trend toward hiring more contingent workers?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The remaining wet steam exits the turbine at 115 kpa with a

consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the

  What tube diameter is required for the model

What tube diameter is required for the model if dynamic similarity is to be maintained between model and prototype?

  How much error would resultin the shaft work out put of the

steam flows through a small turbine at a rate of 10000 kgh entering at 600 degc and 2.0 mpa and emerging at 0.01 mpa

  A stack gas flowing at 80 m3min at t 25 degree c and 1 atm

a stack gas flowing at 80 m3min at t 25 degree c and 1 atm contains approximately 75 n2 5 o2 8 h2o and 12 co2. a

  Assuming constant specific heats for air at room temperature

A well insulated 3-m X 4-m X 6-m room initially at 7 degrees C is heated by the radiator of a steam heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200 degrees C.

  Determine the mass of the air-initial temperature of the air

Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initia..

  Assuming that the heat pump requires 15 kw of power what is

a heat pump maintains a temperature of 25degc inside a house. the house leaks 0.8 kw per degree temperature difference

  Steam at 35 bar and 600 degree k enters a throttling valve

steam at 35 bar and 600 degree k enters a throttling valve that reduces the steam pressure to 7 bar. assuming there is

  Determine the force p that will produce a 2 in vertical

the 1.25 in diameter steel shaft bc is built into the rigid wall at c and supported by a smooth bearing at b. the lever

  The steel bar has the orginal dimensions shown in the

the steel bar has the orginal dimensions shown in the third figure below. if it is subjected to an axial load of 50kn

  The acceleration of a particle traveling along a straight

the acceleration of a particle traveling along a straight line is a8-2s ms2 where s is in meters. if v0 at s0 determine

  Find the complete initial and final states t p v h u and

find the complete initial and final states t p v h u and sdeg for the following ideal gas process air at 260 f and 15

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd