User Account

All Pages

Determine the size and steel grade of axle

Assignment Help Mechanical Engineering
Reference no: EM131136502

I need to determine the size and steel grade of axle needed to given a certain load capacity.

- The axle is supported by a pair of self-aligning bearings near the ends, with the wheel beyond that.

- Currently the axle is 25 dia (1") and the centre of the wheel is 50mm beyond the centre of the bearing.

Peak load will be when the laden trolley is placed on the ground/rails and given the usage I don't see fatigue failure as an issue, hence a fair assumption seems to consider only the static case, as a simply supported beam. In my previous company the design would be handed over to the structural team and likely under gone FEA analysis, however I am now in a much smaller outfit and that option is not open to us, so I am looking for some pointers on appropriate hand calculations and or assumptions.

Reference no: EM131136502

Questions Cloud

What eventual impact on music did the scholacantorum : What eventual impact on music did the ScholaCantorum, Pope Gregory's musical charge to the Benedictines, and Guido de Arezzo have on modern music and education?
Social learning or gottfredson and hirschi general theory : We know that one of the most reliable facts about crime is its relationship to age. Property crime peaks at about 16-17 years of age and violent crime at about 21. Thereafter, both decrease systematically with age.
Create a diagram that demonstrates your personal philosophy : Examine and analyze various diversity theories and apply them to the learning environment. Identify instructional strategies that are applicable to the K-12 diverse learning environment.
Prepare an income statement for august : Prepare an income statement for August, an owner's equity statement for August, and a balance sheet at August 31.
Determine the size and steel grade of axle : I need to determine the size and steel grade of axle needed to given a certain load capacity. The axle is supported by a pair of self-aligning bearings near the ends, with the wheel beyond that
Create a graph for the period 1999-2009 : Create a graph for the period 1999-2009, showing GDP growth rates and the interest rate. Was the EU in a recession in 2001? How did the ECB react to the economic slowdown in the early 2000s?
What regulations are in place to protect chimps and bonobos : What regulations are in place to protect chimps and bonobos in the wild? What restrictions are placed on treatment of bonobos and chimps in captivity, especially those used for psychological and biomedical research?
The following transactions were completed during the month : From an analysis of the owner's equity columns, compute the net income or net loss for April.
Did the low interest rates encourage growth : Compare the graph you obtained with Figure 1 in Box 11-1. Did the low interest rates encourage growth?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the equation which describes the motion what is

a spring is stretched 200mm by a 15kg block. if the block is displaced 100mm downward from its equalibrium position and

  Explain what will the ratio of the angle of twist

What will the ratio of the angle of twist be to that of the hollow shaft if the maximum shear stress in the material of 75 N / mm ^2 and what is the ratio of actual permissible shear stress?

  What is the concentration of protein a in the filtrate as

a hollow fiber membrane separator with a nominal molecular weight cutoff of 100000 is fed a solution of proteins at the

  I is suddenly exposed to an airstream of 10 degc with h

a pure copper sphere with a diameter of 3.0 cm is initially at uniform temperature of 50 degc. it is suddenly exposed

  Modulus of elasticity of the aluminum

1. An aluminum bar 125 mm (5.0 in.) long and having a square cross section 16.5 mm (0.65 in.) on an edge is pulled in tension with a load of 66,700 N (15,000 lbf), and experiences an elongation of 0.43 mm (1.7 X 10-2   in.). Assuming that the defo..

  Determine a the shaft torque required to prevent the

water enters vertically and steadily at a rate of 35 ls into the sprinkler shown in figure q.4. the sprinkler has

  Problem regarding the dynamic viscosity

To a good approximation, the dynamic viscosity µ,, the top surface for g = 1 mm, D= 150 rad/s? What is the total  electric  power  requirement?  What  can  you say thermal conductivity k, and the specific heat cp are inde about the nature of the flow..

  A nozzle for a carbon dioxide co2 fire extinguisher is

a nozzle for a carbon dioxide co2 fire extinguisher is based on the following inlet conditions pressure2500 kpa

  What is the pressure drop associated with the airflow

What is the total rate of heat transfer to the air? What is the pressure drop associated with the airflow?

  Two rigid tanks are connected by a valve tank a contains 02

two rigid tanks are connected by a valve. tank a contains 0.2 m3 of water at 400 kpa and 80 percent quality. tank b

  Calculate the compressor outlet temperature

If the isentropic efficiency of the compressor is 72% and the pressure ratio is 2.2:1, for an inlet pressure and temperature of 1 bar and 25oC, calculate the compressor outlet temperature, the compressor outlet density and the power required to drive..

  Air undergoes an isentropic process from a pressure of 3

air undergoes an isentropic process from a pressure of 3 bar 20degc to a pressure of 1 bar. compute the final

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd