User Account

All Pages

Determine the scalar component of the moment

Assignment Help Mechanical Engineering
Reference no: EM13275809

1 A force. F is applied to a lever - shaft assembly as shown in the figure. F= 534 N. Determine the scalar component of the moment at point 0 about line OB and the reaction at 0.

2456_Average normal and shear stresses on plane.png

2 Two rectangular bars of 10-mm thickness are loaded as shown in the figure. If the average normal stress on plane AA is ISO MPa in compression determine

a. The force Ft

b. The average normal and shear stresses on plane BB.

 

1121_Average normal and shear stresses on plane1.png

Reference no: EM13275809

Questions Cloud

Determine the developed average power : A shot-putter accelerates a 7.28 kg shot from rest to 14.8 m/s. If this motion takes 1.31 s, what average power was developed
How much should be invested in each type of investment : How much should be invested in each type of investment in order to maximize the return? What is the maximum return in the first year? Please show work.
What values of kp and ki will makes to happen : Describe the type of response that would exist if the values of Kp and Ki placed the roots on the boundaries determined in part 1. Note consider each boundaries may exhibit a different performance
Explain what are the spectator ions in the solution : the second contains 0.1 mol Na2S , and the third contains 0.1 mol CaCl2 . What net ionic equations for the precipitation reaction or reactions that occur. What are the spectator ions in the solution
Determine the scalar component of the moment : Determine the scalar component of the moment at point 0 about line OB and the reaction at 0 - average normal and shear stresses on plane BB.
Prepare a simple balance sheet of assets : Assume that Banc One receives a primary deposit of $1 millions. The bank must keep reserves of 20 percent against its deposits. Prepare a simple balance sheet of assets and liabilities for Banc One immediately after the deposit is received.
What was the average coefficient of friction : A skier traveling 11.2 m/s reaches the foot of a steady upward 15.8° incline and glides 10.9 m up along this slope before coming to rest
Explain molar heat capacity and molar internal energy : Next calculate molar internal energy and molar heat capacity assuming vibrational energy levels are not significantly populated at 298 K and do not contribute to molar heat capacity and molar internal energy. Calculate percent error for each molar..
Determine range of k that ensures the system is bibo stable : Given the characteristic equation: F(z) = z^3 + z^2 + kz - 0.5 = 0 a) Use the Jury test to determine the range of "k" that ensures the system is BIBO stable. Show any inequality graphs and how they are combined to determine the valid range of k.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the required wheel diameter to overcome

an industrial water shutoff valve is designed to operate with 30 lb of effort force. The valve will encounter 200 lb of resistance force applied to a 1.5 in. diameter axle. what is the required wheel diameter to overcome the resistance force?

  Will the launch come to rest before hitting the wharf

A launch approaches a wharf at a speed of 10.5 knots(=5.4m/s).The engine are put in the reverse when the launch is 10 m from the wharf, the retardation being 1.25m/s squared. will the launch come to rest before hitting the wharf.. If not, with wha..

  What dielectric constant must the material between the plate

A simple plate capacitor can store 6.5x10^-5 C at a potential of 10000 V. what dielectric constant must the material between the plates have if their area is 6.0x10^-5 m2 and they are 0.16 mm apart?

  How many pounds of downward pressure is placed

approximately how many pounds of downward pressure is placed on a piston in an internal combustion engine at the moment of ignition? I know this will vary some depending on the type fuel, the size of the combustion chamber and ect.

  Determine the initial and final pressures in kpa

Friction between the piston and cylinder wall can be neglected because the process occurs so slowly. For the air, determine the initial and final pressures in kPa and the boundary work for the process in kJ.

  What size of pipe would be required to move

what size of pipe would be required to move 30 milliliters of air in one minute at a pressure of 100 psi.

  Compute reactions of a simply supported continuous beam

Calculate reactions of a simply supported continuous beam. A beam is simply supported at the ends and is continuous over two spans.

  Find the power rating of the electric heater

find (a) the power rating of the electric heater and (b) the temperature rise that the air experiences each time it passes through the heater.

  Coding for computerized relative allocation of facilities

How to do matlab coding for computerized relative allocation of facilities technique

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  Calculate the quality of the system

calculate the quality of the system to begin with. calculate the amount of liquid water to begin with. calculate the heat transfer during the heating process.

  Determine the height to which the pulley is lifted

a simple pulley with the given radius r used to lift heavy objects is positioned 10 feet above ground level. Given that the pulley rotates theta degrees, determine the height to which the pulley is lifted.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd