Determine the required stiffness k of the hydraulic

Assignment Help Mechanical Engineering
Reference no: EM13619835

The jet engine (mass m = 400kg) of a passenger airplane is attached to the plane's wing by a connector that has an effective stiffness of k = 640 x 10^9 N/m and an effective damping coeffcient of c = 3.0 x 10^6 N ·sec/m. In order to save weight the connector is designed with a natural frequency that is smaller than the jet engine's nominal operating frequency, which is w = 8 x10^4 rad/sec. This means that when the engine is powered up it will produce a forcing function that acts on the connector and resonance will occur when the engine reaches the connector's natural frequency. This would cause the connector to experience large deformations and possibly fail.

To avoid such a failure, the connector design calls for a hydraulic stiffener that will temporally increase the connector's stiffness and therefore its natural frequency. The stiffener acts in parallel with the connector and is activated when the engine frequency reaches 70% of the connector's natural frequency (without the stiffener). Once the engine reaches a frequency of 120% of the connector's natural frequency the stiffener is turned off.

Determine the required stiffness k of the hydraulic stiffener such that the response amplitude C/fo of the connector does not exceed 2 during the jet engine power up.

Reference no: EM13619835

Questions Cloud

A 380 muf capacitor that is initially uncharged is : a 3.80 muf capacitor that is initially uncharged is connected in series with a 7.60 k ohm resistor and an emf source
What is the resistance in an rl circuit with l 3821 mh if : what is the resistance in an rl circuit with l 38.21 mh if the time taken to reach 83.0 of its maximum current value
The average length of a new born baby is 20 inches with a : the average length of a new born baby is 20 inches with a standard deviation of 1 inch.b. if n100 what is the mean of
A stock has an expected return of 12 percent its beta is : a stock has an expected return of 12 percent its beta is 1.30 and the risk-free rate is 5 percent. what must the
Determine the required stiffness k of the hydraulic : the jet engine mass m 400kg of a passenger airplane is attached to the planes wing by a connector that has an
The ball travels straight upward in the absence of air : a small lead ball attached to a 1.6-m rope is being whirled in a circle that lies in the vertical plane. the ball is
Health insurance in america was forever changed by the : select one of the major u.s. government programs for funding of health care services and explain the scope and role of
A slingshot fires a pebble from the top of a building at a : a slingshot fires a pebble from the top of a building at a speed of 11.1 ms. the building is 30.5 m tall. ignoring air
Lang industrial systems company lisc is trying to decide : lang industrial systems company lisc is trying to decide between two different conveyor belt systems. system a costs

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd